Your SlideShare is downloading. ×
  • Like
  • Save
2010 Interworks EQ
Upcoming SlideShare
Loading in...5
×

Thanks for flagging this SlideShare!

Oops! An error has occurred.

×

Now you can save presentations on your phone or tablet

Available for both IPhone and Android

Text the download link to your phone

Standard text messaging rates apply

2010 Interworks EQ

  • 569 views
Published

This is a copy of the 2010 presentation on Interworks EQ that I do for P201, P103 and P201-I. At the end of this presentation you will find a video covering the basics of specification on YouTube. If …

This is a copy of the 2010 presentation on Interworks EQ that I do for P201, P103 and P201-I. At the end of this presentation you will find a video covering the basics of specification on YouTube. If you have any questions regarding the content of this document please reach out to alibia.devente@gmail.com

Published in Design , Business , Technology
  • Full Name Full Name Comment goes here.
    Are you sure you want to
    Your message goes here
    Be the first to comment
    Be the first to like this
No Downloads

Views

Total Views
569
On SlideShare
0
From Embeds
0
Number of Embeds
1

Actions

Shares
Downloads
0
Comments
0
Likes
0

Embeds 0

No embeds

Report content

Flagged as inappropriate Flag as inappropriate
Flag as inappropriate

Select your reason for flagging this presentation as inappropriate.

Cancel
    No notes for slide
  • End Caps are discontinued.End Trim are required.
  • Panel Details:The Tackable Acoustical (Monolithic) panels now meet the GSA Noise Reduction Coefficient (NRC) requirement of .65 for Acoustical panels, improved from .35 NRC. The Sound Transmission Coefficient (STC) stays the same at 15.The Sectional panels NRC improved to .60 with an STC of 14.Sectional panels are now tackable.Sectional panels have a Class A fire ratingsame as Monolithic.Sectional panels are in process of becoming SCS certifiedStacking panels now have the capacity to run cables and remain load bearing.
  • You could re-fabric the panel by ordering a new monolithic tile as a service part. Glass panels are also available.
  • 10P Stack panels can not be added to panels manufactured after 2.26.07.Stack is available in 12”, 14” and 18” panel heights.The width of the stack panel must match the width of the lower panel.Stack panels are available in either fabric or glass.
  • While this page is not listed in the pricelist it is relative to discuss in this section.
  • Only the first stack is load bearing.
  • Note 22 cables and 11 in passing.
  • Images on the web reflect the new images of the product. Get Images on KOP have a variety of new and old images. Anything with 09 is a current image.Replace the image of the EQ panel when available as this is the old model number.You will find the comprehensive pricelist includesthe new Interworks EQ information.
  • Why change?Improvement in tackable acoustical (monolithic) and sectional tiles attachment to the frames - Enhancing sustainability and installationFactory installation of the sectional tiles to the frames – Eliminating over 80% of frame and tile packaging, and reducing overall waste being disposed of during installation – 15 tons per year – and installation time Enhanced application of panel fabrics - Elimination of potential for fraying, tear-through, "window framing," or stringsTop cap clip eliminated – simplifying the component for easier installation Extruded aluminum tubing frame replaced by 1¼" steel tubing, panel core is open, and the Styrofoam and pressboard in panels and sections and have been replaced with fiberglass – improving sustainabilityThe design of glass panels and tiles has also been improved with a consistent frame size on all four sides.
  • Old Model Numbers are 10PNew Model Numbers are 11P
  • Some service may cost more based on consolidated model numbers. Service parts can be found on kimballoffice.com when you sign in. Not all service parts will work interchangeably given there are slight differences with 10P and 11P model numbers. Example: top cap
  • 10P Stack panels can not be added to panels manufactured after 2.26.07.Stack is available in 12”, 14” and 18” panel heights.The width of the stack panel must match the width of the lower panel.Stack panels are available in either fabric or glass.

Transcript

  • 1. We will be starting momentarily.
    For Audio Please Dial:
    Conference Call 888.481.3032
    Passcode 75892620#
    Press *6 to mute phone on/off
  • 2. Create useful work spaces without jeopardizing your budget.
  • 3. Stylish Options for smart settings:
    Clear or frosted glass
    Pass-thru tiles
    Fabric-wrapped corner pieces
    Tackable fabric panels
    Create the space your facility needs:
    Reception areas
    Meeting rooms
    Private offices
    Touchdown spaces
  • 4. Panel Statement of Line
    Page 206
    Interworks is our easy, simple and quick solution.
    The Interworks panel system is priced at all fabric grade levels.
    Interworks has a metal top cap and a polymer hinge.
    The glass panel is ¼” thick.
    The door is 1 7/16” thick.
    Traxx and Tiles integrate with this product.
    Tackable Acoustical Panel
    Glass Panel
    Tackable Sectional Panel
    Stackable Panels
    Privacy Panels
    Hinged Doors
    Tackboards
  • 5. Connectors and Trim Statement of Line
    Page 207
    The connector is made up of a polymer hinge that (2) ship with each panel.
    Extra hinges are recommended to be placed at the end of a run for reconfigurations.
    End trims are required.
    End caps are for panels manufactured prior to August 31, 2009.
    Finish channels simply make a clean directional connection. The polymer hinge actually makes the connection.
    Trim Top Caps
    End Caps
    Finish Channels
    Wall-Mount Connectors
    End Trim
    Traxx Starter Kit
  • 6. Power and Data Statement of Line
    Page 208
    Panels ship with a power distribution if specified.
    Jumper cables are used to continue power from one panel to another.
    The base power entry can enter from the side, at a connection or end of run.
    The electrical system is 8-wire.
    All power runs in the base of the panel.
    Data runs at the top with the capability of holding 8 wires at the base.
    Think of managing cords below the surface.
    Duplex Receptacles
    Base Power Entry
    Power Distribution Assemblies
    Jumper Cables
    New York City Electrical
    Ceiling Power Entry
    Hardwire Electrical
    Power/ Data Poles
    Data
    Components
    Data
    Channels
    Vertical Cable Manages
  • 7. Interworks EQ Overview
    Page 209
    The current 11P model number panel was introduced on August 31, 2009.
    The crowned top cap profile is available only painted .
    Panel Thickness is 2”
    An in-line connector must be specified between two panels sold in sets of two.
    Panel has hinge connection
    Wirewaycovers offer variations in
    punch options.
    You can add stack to change heights
  • 8. Interworks EQ Acoustical Panel Details
    Page 210
    The hinge is a continuous flexiform polymer hinge.
    Side rails provide slots at 1” increments for mounting components.
    Cable routing offers 8 data cables to be routed at the bottom of the panel, that is 4 per side.
    The sides of the panel are not finished.
    Image taken from the pricelist.
  • 9. Interworks EQ Acoustical Panel Details
    Page 210
    Panel is created from 1 ¼” steel tubing. The center of the frame is open with two sheets of tackable fiberglass.
    Panel includes:
    Top cap
    Wireway covers
    Panel hinges
    Glides and carpet grippers
    Frame with tiles
    NRC rating .65
    STC rating 15
  • 10. Interworks EQ Sectional Frames
    Page 212
    Sectional Frames Include:
    Top cap
    Wireway covers
    Panel Hinges
    Glides and Carpet Grippers
    Frame with Tiles
    The mid-wireway panel is a type of sectional panel.
    Image taken from installation instructions.
  • 11. Interworks EQ
    Mid-Wireway Panel
    Page 210
    This panel is only available in a powered option.
    The panel ships with a harness at the base and mid-height including the jumper
    Power can not pass from one panel at mid-height to another.
    Tiles ship with the frame.
    The power components can also be added at a later point if you have an existing sectional frame.
  • 12. Interworks EQ Sectional Panel
    Page 213
    Two tiles are required for each segment however tiles shipped in place, can be moved.
    The sizes indicated must be used in the location specified.
    Fabric is tackable.
    The glass tile has an even frame on all four sides which is similar to stack.
    Metal is embossed or plain front.
    Image taken from the pricelist.
  • 13. Interworks EQ Stackable Panel
    Page 214
    Two stack panels can go on top of any one panel.
    Only the first stack panel is load-bearing.
    Stack height cannot exceed 80”
    A change at height cannot occur at a connector.
    Data cables can be placed inside the stack panel.
    10P and 11Pbase models must match 10P and 11P stack models.
    A full end-trim is required.
  • 14. Interworks EQ Privacy Panels
    Page 215
    Privacy Panels are for visual privacy only as it does not lock or latch.
    Doors should always open inside a station.
    The privacy panel is non-handed and reversible.
    Privacy Panels Include:
    Top attachment bracket
    Base pivot bracket
    Caster
    Image taken from the pricelist.
  • 15. Interworks EQ Hinge Door
    Page 216
    Hinge Door Includes:
    Frame and threshold
    Top cap
    Panel Hinges
    In-line connector caps
    A 42” door is required to meet ADA.
    A locking lever is also available.
    The door is 1 7/16” thick.
    Be sure to use the stabilizer brackets to reinforce the connection.
    Image taken from the pricelist.
  • 16. Interworks EQ Finish Channels and Trim Top Caps
    Page 217
    A finish channel is necessary to complete a directional turn.
    An XTC1 connector top cap is required in finishing a 4-way transition.
    A finish channel includes:
    Fabric Channel
    Finish channel top cap
    Metal base cover
    Alignment clip
    Image taken from the pricelist and installation instructions.
  • 17. Interworks EQ Finish Channels and Trim Top Caps Cont…
    Page 217
    Note the new hi-lo at a connector.
    In some instances you may be required to specify two parts for a hi-lo condition.
    Image taken from installation instructions.
  • 18. Interworks EQ Power & Data Channels
    Page 217
    When the height is dropped or raised the cables at the top of the panel must transition. The openings provided by the data channel allows for the flow of cabling to continue
    A finish channel is not required where a data channel is used at a directional transition.
    These images were taken from the pricelist.
  • 19. Interworks EQ Traxx Starter Panel
    Page 218
    Interworks EQ offers a connection with Traxx that can go from all points within the space plan offering the greatest flexibility in reconfiguration.
    Interworks EQ offers a full height end trim to finish exposed edges of Traxx.
    It is not recommend to wall-start the start and end points of Traxx.
    Image taken from installation instructions.
  • 20. Traxx with Interworks EQ
    Page 218
    The Interworks connection is more clean given the polymer hinge panel connection.
    When joining Interworks EQ to Traxx be sure to use the tiles specified for this connection as tiles will not need to be modified in the field if the wrong height is selected.
  • 21. Traxx with Interworks EQ
    in CAP
    You can start the Interworks panel from the edge of Traxx based on the full end trim.
    Image was taken from CAP.
  • 22. Panel spacing with Traxx in CAP
    In this instance a different panel type was used. Interworks EQ is a 2” thick panel so the dimension would need to be considered for general planning purposes.
    Image was taken from CAP.
  • 23. Interworks EQ Application Guidelines
    For Panel Configurations without Components
    Page 219
    Image taken from the pricelist.
  • 24. Interworks EQ Application Guidelines
    For Panel Configurations without Overhead Storage
    Page 220
    Remember to follow minimum wing width rules noted on each page.
    See page 251 For supplemental brackets.
    Image taken from the pricelist.
  • 25. Interworks EQ Supplemental Brackets
    Page 273 & 274
    These brackets are recommend for use when panels join without a worksurface.
    Supplemental brackets are suggested
    but not required.
  • 26. Interworks EQ Application Guidelines
    For Panel Configurations with Overhead Storage
    Page 221
    Remember to follow minimum wing
    width rules noted on each page.
    See page 251 For supplemental brackets.
  • 27. Interworks EQ Application Guidelines
    For X-Configurations
    Page 222
    Remember to follow minimum wing width rules noted on each page.
  • 28. Interworks EQ Application Guidelines
    For 120⁰ V- and Y- Configurations
    Page 223
    Do not exceed maximum number of panels in a run.
    Remember to follow minimum wing width rules noted on each page.
  • 29. Interworks EQ Application Guidelines
    For Wall- and Traxx-Mounted Panel Configurations
    Page 224
    Do not exceed maximum number of panels in a run.
    Remember to follow minimum wing width rules noted on each page.
  • 30. Interworks EQ Application Guidelines
    For Stackable Panels
    Page 225
    Maximum stack height is 80”.
    Two stackable panels can go on top of any one panel.
    You cannot change height at a connector.
    If placing overheads on one side it is required to use the stackable load brackets from page 251.
  • 31. Interworks EQ Tackboards
    Page 275
    Interworks EQ panels are fully tackable.
    Tackboards are available as either
    15” or 19” high.
    15” tackboards with 62’ panels
    19” tackboards with 66” panels.
    You have the option of specifying the tackboards with
    panel fabric (Grade A, B, COM)or seating fabric (Grade 1 or 2).
    Up to two tackboards may be mounted on one panel.
  • 32. Interworks EQ Trim Caps
    Page 280 & 281
    Interworks EQ trim caps are applied based on directional transitions to conceal gaps.
  • 33. Interworks EQ Power and Data Overview
    Page 226
    When mixing the electrical system with generation one consult you Product Specifer for specification tips.
  • 34. Interworks EQ Power Distribution Assemblies and Receptacles
    Page 227
    Power Distributions match the same size as the panel.
    You can add a power distribution to a non-powered panel.
    Interworks EQ is an 8-wire system.
  • 35. Interworks EQ Jumpers
    Page 227
    Jumpers are used to continue power from panel to the next.
    Mid-height jumpers are included with the mid-height powered panel.
    18” wide panels have no electrical access however they can accept pass-thru jumpers cables.
  • 36. Interworks EQ Floor Power Entry
    Page 228
    A base feed specification is specified based on the point of entry. A finished base plate will ship for a clean connection.
  • 37. Interworks EQ Ceiling Power Entry and Power/ Data Poles
    Page 228
    The Ceiling Power Entry is specified separate from the ceiling power/ data pole.
    An extended can be specified for the power/ data pole through customer care.
    A finish channel is not required when a power/ data pole is used.
  • 38. Interworks EQ Hardwire Components
    Page 229
    A side feed plate is offered however you can insert the power entry from the end, corner and straight position.
  • 39. Interworks EQ New York City Power Assemblies
    Page 230
    The power entry is not available for 18” and 24” wide panels only 30” to 60”.
    Duplex receptacles cannot enter into this power entry however data ports can be added.
    All panels are purchased non-powered.
    Mid-Wireway panels are not available for New York.
  • 40. Interworks EQ
    8-wire Electrical System
    Page 231 & 232
    .
  • 41. Interworks EQ Cable Management
    Page 233
    The panel is designed to hold all data at the top and all electrical at the bottom.
    Eight cables can be run at the bottom of the panel, 4 per side.
    You can not place data cables at the top of a stack panel.
    When adding stack on top of a monolithic panel you are encapsulating the data within the panel.
    Data channels allow cables to drop at a lower panel.
  • 42. Interworks EQ Worksurface Brackets
    Important: Brackets must be specified separately.
    1 3/16” surfaces need support every 48”
    1 9/16” surfaces need support every 60”
    Cantilevers are handed.
    Flat brackets are sold individually however must be used in pairs with a cantilever when located at the seam of two surfaces.
    Edge brackets at corner locations are not specific to hand of bracket.
  • 43. Interworks EQ Application and Support
    Page 332 & 333 (Footprint)
  • 44. Interworks EQ Cantilever
    Page 450 (Footprint)
    Important: Brackets must be specified separately.
    Cantilevers are handed.
    Flat brackets are sold individually however must be used in pairs with a cantilever when located at the seam of two surfaces.
    Consider placing pedestal fillers behind pedestals to fill gap.
  • 45. Interworks EQ Edge Support Brackets
    Page 449 (Footprint)
    Important: Brackets must be specified separately.
    Edge brackets at corner locations are not specific to hand of bracket.
    It is not recommended to place edge brackets in the center of runs this image simply conveys all possible locations.
  • 46. Interworks EQ Overhead Brackets
    Overview
    Wood/ Laminate overheads cannot be hung on Interworks EQ.
    Overhead Brackets
    Page 520 (Footprint)
    Ganging Brackets
    Page 523 (Footprint)
    .
  • 47. Interworks EQ Flat and Bevel Profile Overhead Brackets
    Page 524 (Footprint)
    You will not find a bracket for this overhead is apart of the construction.
    Ganging brackets are sold
    in a quantity of 4.
    .
  • 48. Interworks EQ Lunar Profile Overhead Brackets
    Page 524 & 526 (Footprint)
    A set of overhead brackets is need for each overhead regardless of width.
    Ganging brackets are sold individually
    .
  • 49. Kimball Office Resources
    Dealer Sales Manager
    Customer Care/ By Design
    800.482.1818
    Product Technical Support
    800.481.6696
    Product Specifier
    Alibia de Vente
    Market Education
    770.265.4006 or
    Alibia.devente@kimball.com
  • 50.
  • 51. www.kimballoffice.com
  • 52. www.kimballoffice.com
    Working with multi-generations of Interworks EQ panels can be solved in most cases by knowing just a few tips.
  • 53. Interworks EQ Comparisons
    Previous generation model number
    started with 10P
    New generation of panels start with 11P.
    You cannot combine new and old generation stack however panels will remain easily attached side-by-side.
    New -11P Sectional / Old - 10P Sectional
    Old -10P Monolithic / New - 11P Monolithic
  • 54. Interworks EQ
    Is it 10P or 11P?
    Close up of where the two rails meet.
    The horizontal rail is for holding the tiles in only and not supporting worksurfaces or components.
    The corner details between the monolithic panels and sectional show a crisp corner detail.
    The frame detail on sectional / stack glass has an even frame on all side.
    New varied height 3-way model number.
    Full End trim and hi-lo trim is required not as you will notice connection points on the frame is removed.
    .
    Old 10P Stacking on 10P Sectional.
    New - 11P Frame Profile Old - 10P Frame Profile
  • 55. Interworks EQ
    List Price Comparison
    This price has not been confirmed
    as of 8-19-09.
  • 56. Interworks EQ
    Sectional
    Panel Frames
    Planning Page 212 & 213 of the January 15, 2010 rules remain applicable.
    The 10P model required tiles to be ordered as a separate line item (left).
    The 11P model is specified based on tile position from the top location down.
    Image taken from previous and current installation instructions.
    Previous Generation - 10P Sectional
    Current - 11P Sectional
  • 57. Interworks EQ Sectional Panel
    The 54” panel which had a 6” sectional tile segment was discontinued.
    The 54” sectional panel shown on the right with the 20” segment at top remains available.
    Image taken from the October 2009 electronic pricelist.
  • 58. Interworks EQ Stackable Panel
    Two stack panels can go on top of any one panel manufactured after 2.26.07.
    Only the first stack panel is load-bearing.
    Stack height cannot exceed 80”
    A change at height cannot occur at a connector.
    Data cables cannotbe placed inside a 10Pstack panel.
    10P and 11Pbase models must match 10P and 11P stack models.
    A full end-trim is required.
  • 59. Interworks EQ Supplemental Brackets
    Page 273 & 274
    These brackets are recommend for use when panels join without a worksurface.
    Supplemental brackets are suggested
    but not required.
    This image conveys 10P models numbers. The bracket spacer is not required for 11P panels unless joined.
  • 60. www.kimballoffice.com