Your SlideShare is downloading. ×
Honeywell gsmvlp5-honeywell-ilp5-install-guide
Honeywell gsmvlp5-honeywell-ilp5-install-guide
Honeywell gsmvlp5-honeywell-ilp5-install-guide
Honeywell gsmvlp5-honeywell-ilp5-install-guide
Upcoming SlideShare
Loading in...5
×

Thanks for flagging this SlideShare!

Oops! An error has occurred.

×
Saving this for later? Get the SlideShare app to save on your phone or tablet. Read anywhere, anytime – even offline.
Text the download link to your phone
Standard text messaging rates apply

Honeywell gsmvlp5-honeywell-ilp5-install-guide

454

Published on

Published in: Technology, Business
0 Comments
0 Likes
Statistics
Notes
  • Be the first to comment

  • Be the first to like this

No Downloads
Views
Total Views
454
On Slideshare
0
From Embeds
0
Number of Embeds
0
Actions
Shares
0
Downloads
8
Comments
0
Likes
0
Embeds 0
No embeds

Report content
Flagged as inappropriate Flag as inappropriate
Flag as inappropriate

Select your reason for flagging this presentation as inappropriate.

Cancel
No notes for slide

Transcript

  • 1. 800-08115 1/11 Rev. B GSMVLP5 GSM and ILP5 Ethernet Communications Modules Installation and Setup GuideInstalling Communication Modules RF Exposure WARNING: The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna(s) or transmitter.Installing the GSMVLP5 in the LYNX Touch Series Control Ensure that SIM card and the connector board are securely installed in the GSMVLP5 before installing the module in the LYNX Touch.1. Install the provided FCC/IC label (P/N 800-08334) on the control’s case back (refer to Figure 1). LYNX TOUCH SERIES FCC ID: CFS-8DLLYNXTOUCH1 IC: 573F-LYNXTOUCH1 IC MODEL: LYNXTOUCHG1 CONTAINS TRANSMITTER MODULE FCC ID: QIPMC55I IC: 7830A-MC55I 800-08334 2/11 Rev A LYNX TOUCH SERIES FCC ID: CFS-8DLLYNXTOUCH1 IC: 573F-LYNXTOUCH1 IC MODEL: LYNXTOUCH1 THIS DEVICE COMPLIES WITH PART 15 OF FCC RULES AND RSS 210 OF INDUSTRY CANADA. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. COMPLIES WITH FCC RULES, PART 68 FCC REGISTRATION NO.: AC3AL05BL5000 RINGER EQUIVALENCE: 0.1B 800-08126 1/11 Rev A 5000-100-186-V0 Figure 1. FCC/IC Label Location2. Release the LYNX Touch front case from the back case by depressing the two locking tabs at the top of the unit with the blade of a medium size screwdriver (Refer to Figure 2).3. Install the GSMVLP5 into the LYNX Touch control front case. Ensure that the connector board is properly seated into the receptacle on the control (Refer to Figure 2).4. Secure the GSMVLP5 with the three provided screws (Refer to Figure 2).5. Enable the GSMVLP5 device, configure alarm reporting and module supervision and register the device. Refer to the “Program the Radio” and “Diagnostics” sections in the LYNX Touch Series Installation and Setup Guide (P/N 800-06834 or higher). For Documentation and Online Support: http://www.security.honeywell.com/hsc/resources/MyWebTech
  • 2. CONNECTOR SCREW BOARD (3) CONNECTOR BOARD SIM CARD ROTATED 180 GSMVLP5 RECEPTACLE LYNX TOUCH LOCKING TABS 5000-100-151-V1 Figure 2. Installing the GSMVLP5 in the LYNX TouchInstalling the ILP5 in the LYNX Touch Series Control Ensure that the connector board and cable are securely installed in the ILP5 before installing the module in the LYNX Touch.1. Release the LYNX Touch front case from the back case by depressing the two locking tabs at the top of the unit with the blade of a medium size screwdriver (Refer to Figure 3).2. Using a wire cutter or knife cut the plastic tabs that secure the ILP5 spacer to the back case of the LYNX Touch (Refer to Figure 3).3. Remove the ILP5 receptacle knockout from the left side of the LYNX Touch back case (Refer to Figure 3).4. Install the ILP5 into the LYNX Touch control front case. Ensure that the connector board is properly seated into the receptacle on the control (Refer to Figure 3).5. Secure the ILP5 with the three provided screws (Refer to Figure 3).6. Insert the ILP5 receptacle and spacer into the slot on the back case (Refer to Figure 3).7. Secure the communications cable to the tie wrap point on the ILP5 with the provided tie wrap (Refer to Figure 3).8. Enable the ILP5 and configure alarm reporting and module supervision and register the device. Refer to the “Program the Radio” and “Diagnostics” sections in the LYNX Touch Series Installation and Setup Guide (P/N 800-06834 or higher). For Documentation and Online Support: http://www.security.honeywell.com/hsc/resources/MyWebTech
  • 3. ETHERNET CABLETO ILP5 RJ45 RECEPTACLE LYNX TOUCHALTERNATE INSTALLATION REMOVE ILP5 REMOVE ILP5 KNOCKOUT SPACER ILP5 SPACER RJ45 RECEPTACLECONNECTOR BOARD ROTATED 180 TIE WRAP (1) TIE WRAP POINT CONNECTOR BOARD SCREW (3) ILP5 RECEPTACLE LYNX TOUCH LOCKING TABS 5000-100-154-V1 Figure 3. Installing the ILP5 in the LYNX Touch
  • 4. Electrical SpecificationsGSMVLP5Voltage Input 5VCurrent Idle 15 mA, standby Average 300mA, average transmit Peak 1.6A peak transmit, 25% duty cycleILP5Voltage Input 5VCurrent: 83 mA, 100 Base T with traffic 41 mA, 10 Base T with traffic 2 Corporate Center Drive, Suite 100 P.O. Box 9040, Melville, NY 11747 Copyright © 2011 Honeywell International Inc. www.honeywell.com/securityÊ800-08115!Š800-08115 1/11 Rev. B

×