Furniture components
Upcoming SlideShare
Loading in...5
×
 

Furniture components

on

  • 655 views

 

Statistics

Views

Total Views
655
Views on SlideShare
655
Embed Views
0

Actions

Likes
0
Downloads
0
Comments
0

0 Embeds 0

No embeds

Accessibility

Categories

Upload Details

Uploaded via as Microsoft Word

Usage Rights

© All Rights Reserved

Report content

Flagged as inappropriate Flag as inappropriate
Flag as inappropriate

Select your reason for flagging this presentation as inappropriate.

Cancel
  • Full Name Full Name Comment goes here.
    Are you sure you want to
    Your message goes here
    Processing…
Post Comment
Edit your comment

Furniture components Furniture components Document Transcript

  • Furniture Fittings and Accessories Components Chair Parts Heavy Duty Swivel 12 gauge steel with a double race 10 1/4 by 10 1/4 flat pitch. Mounting holes are on 8" centers Swivel Rocker base Brown legs with plastic feet. Leg span is 25" and comes in either a 5 1/4" or 6" overall height. Steam Bent Oak Rocker Runners Length measures strait across from tip to tip. Stronger than cut rockers Sold in pairs only. Unfinished red oak will require drilling sanding and finishing. 1 5/16" high by 34 1/4" long by 5/8" thick 1 5/16" high by 34 1/4" long by 1 1/8" thick 1 5/16" high by 34 1/4" long by 1 7/8" thick Cut Oak Rocker Runners 1 3/4" high by 34 1/2" long by 1 1/16" thick 1 3/4" high by 37" long by 1 9/16" thick Curved Rocking Chair Seat Oak face and back. It must be shaped and cut to fit your particular rocker. Send us a sketch of your formed shape before ordering to make sure it will fit. We can provide this one curvature only. Our supplier doesn't have any other zaini@selectvest.com Wisdom Management Services (M) Sdn. Bhd. 1
  • Furniture Fittings and Accessories Components shape molds. 24" to 25"long following the curve. 3/16" thick, 20" plus wide. Oak Hip Huggers 6 1/2" high by 5 1/4" deep by 7/8" diameter. 11" long from tip to tip measuring along the curve. **Please note: All measurements are approximate. One end is sanded flat to fit the chair seat. The other end is carved out to fit the back spindle. Screw holes are pre-drilled. Unfinished, sanded, ready to install. Ends are pointed. One left hand and one right hand hip hugger required per chair. Sold in pairs only. Hip hugger Clips Outside dimensions - 1" long by 11/16" wide by 1/2" high. Screw hole - 1/4" diameter. Made to fit 7/8" hiphuggers. Sold in sets of four. Morris Chair Brackets 7 3/4" long by 15/16" wide. Hooks will accommodate 3/8" to 1/2" diameter rods. The common angle of the brackets will adapt to the curve of most Morris chairs. Sold by the pair. Morris Chair Rod Overall - 29 3/4" long. Rod - 28 1/4" long by 3/8" diameter. Beehive finials - 3/4" long by 7/8" diameter. Finials are attached with set screws which can be removed, allowing the rod to be cut to length if necessary. zaini@selectvest.com Wisdom Management Services (M) Sdn. Bhd. 2
  • Furniture Fittings and Accessories Components Platform Rocker Springs All springs are sold by the pair which will do one chair. Heavy Duty - 7 gauge Eight turns. Single Juvenile Platform Rocker Springs. Oak High Chair Parts 20 1/2" wide 11 3/4" deep. 1 3/32" thick with Routed center. 16" wide by 8 1/2" deep at center. 7" deep at ends. 16" wide by 8" deep. Bent Oak High Chair Tray Arms Overall length - 18 1/2" long 23" long following the curve. Flat area - Approximately 13" 7/8" Square. Sold by the pair with spacers. High Chair Tray Hardware Arm piece - 6" L x 5/8" w x 7/8" deep. Tray Piece - 3 5/16" L x 1" w x 15/16" deep. Best for use with our W3-5226 tray or similar styles only. Comes as a set for attaching one high chair tray. The long piece attaches to the outside of the arm. The short piece attaches to the underside of the tray. The spring loaded clamp allow the position of the tray to be adjusted then locked into zaini@selectvest.com Wisdom Management Services (M) Sdn. Bhd. 3 View slide
  • Furniture Fittings and Accessories Components place. High Chair Safety Strap 13" long by 5/8" wide Natural leather. Includes screw snap for easy installation. Finials, Spindles, Pegs 5 inches tall and 3 inches in diameter Pine Pine fence post finial 4 1/2" tall and 3" Turned length - 2 1/4" Overall length - 3 1/8" Maximum diameter - 15/16" Tenon diameter - 3/8" zaini@selectvest.com Wisdom Management Services (M) Sdn. Bhd. 4 View slide
  • Furniture Fittings and Accessories Components Turned length - 3 3/32" Overall length - 3 3/4" maximum diameter - 1 5/8" Tenon diameter - 3/8" Turned length - 2" Overall length - 2 7/16" Maximum diameter - 13/16" Tenon diameter - 1/2" zaini@selectvest.com Wisdom Management Services (M) Sdn. Bhd. 5
  • Furniture Fittings and Accessories Components Turned length - 3 3/32" Overall length - 3 3/4" maximum diameter - 1 5/8" Tenon diameter - 3/8" Turned length - 2" Overall length - 2 7/16" Maximum diameter - 13/16" Tenon diameter - 1/2" zaini@selectvest.com Wisdom Management Services (M) Sdn. Bhd. 5