DIY the Quadcopter
Are you dreaming about DIY a cool quadcopter by yourself one day?Today ICStation Team will
share you th...
3.Prepare and install the main parts of engine body.
4.Use Desktop miniature bench drill to process rack.

5.Use the original propeller protector to fix these two EPP1045 prop...
6.Weld Banana pin
7.Install and fix the motor
8.The whole structure of rack.
9.To modify the remote control FT06-C
Based on the cheap and big size FT06-C, add two ratio channel and LCD to display the relevant
parameter.Leave the high fre...
11.Take down the original PPW board of FT06-C
12.Put one board in this place.
13.Add a 5110 LCD in this place of FT06-C
14.Weld the PPM control board

15.Successfully light the LCD

16.Look the whole effect after adding the LCD.
17.Install the potentiometer of the left and right side.
18.Wire the LCD and potentiometer
19.Look the tew added potentiometer.

20.Increase the height of potentiometer knob
21.Calibration the central point of the rocker in engineering mode.

22.Display valid values of PPM in front 6 channels wh...
23.The PPM waveforms of 8 channel displaying through the receiver

24.Flight testing in G3.5
DIY Quadcopter with 51 MCU C8051F 2212 KV930 Motor German EPP1045
Upcoming SlideShare
Loading in...5
×

DIY Quadcopter with 51 MCU C8051F 2212 KV930 Motor German EPP1045

441

Published on

Published in: Self Improvement
0 Comments
0 Likes
Statistics
Notes
  • Be the first to comment

  • Be the first to like this

No Downloads
Views
Total Views
441
On Slideshare
0
From Embeds
0
Number of Embeds
2
Actions
Shares
0
Downloads
18
Comments
0
Likes
0
Embeds 0
No embeds

No notes for slide

DIY Quadcopter with 51 MCU C8051F 2212 KV930 Motor German EPP1045

  1. 1. DIY the Quadcopter Are you dreaming about DIY a cool quadcopter by yourself one day?Today ICStation Team will share you the making steps with a lot of ultra-clear pictures. The quadcopter we introduce to you uses framework of 51MCU and all modules of system based on C8051F.The rack is made of electric straight liner and tube socket with hard disk slice.The motor uses 2212 KV930. The front and back side of propellers use German EPP1045. 1.Prepare two Hard Disk. These are two second-hand hard disk. 2.Install the base of electric straight liner
  2. 2. 3.Prepare and install the main parts of engine body.
  3. 3. 4.Use Desktop miniature bench drill to process rack. 5.Use the original propeller protector to fix these two EPP1045 propellers .
  4. 4. 6.Weld Banana pin
  5. 5. 7.Install and fix the motor
  6. 6. 8.The whole structure of rack.
  7. 7. 9.To modify the remote control FT06-C
  8. 8. Based on the cheap and big size FT06-C, add two ratio channel and LCD to display the relevant parameter.Leave the high frequency control head and replace whole PPM encoding board. 10.Cutting the board with the specialized knife.
  9. 9. 11.Take down the original PPW board of FT06-C
  10. 10. 12.Put one board in this place.
  11. 11. 13.Add a 5110 LCD in this place of FT06-C
  12. 12. 14.Weld the PPM control board 15.Successfully light the LCD 16.Look the whole effect after adding the LCD.
  13. 13. 17.Install the potentiometer of the left and right side.
  14. 14. 18.Wire the LCD and potentiometer
  15. 15. 19.Look the tew added potentiometer. 20.Increase the height of potentiometer knob
  16. 16. 21.Calibration the central point of the rocker in engineering mode. 22.Display valid values of PPM in front 6 channels when working.
  17. 17. 23.The PPM waveforms of 8 channel displaying through the receiver 24.Flight testing in G3.5

×