• Share
  • Email
  • Embed
  • Like
  • Save
  • Private Content
シンプルモデル:トランスモデルのパラメータ及び説明について
 

シンプルモデル:トランスモデルのパラメータ及び説明について

on

  • 872 views

シンプルモデル:トランスモデルのパラメータ及び説明について

シンプルモデル:トランスモデルのパラメータ及び説明について

Statistics

Views

Total Views
872
Views on SlideShare
682
Embed Views
190

Actions

Likes
0
Downloads
1
Comments
0

5 Embeds 190

http://beetech-icyk.blogspot.jp 130
http://beetech.dgblog.dreamgate.gr.jp 31
http://beetech-icyk.blogspot.com 26
http://beetech-icyk.blogspot.kr 2
https://twitter.com 1

Accessibility

Upload Details

Uploaded via as Adobe PDF

Usage Rights

© All Rights Reserved

Report content

Flagged as inappropriate Flag as inappropriate
Flag as inappropriate

Select your reason for flagging this presentation as inappropriate.

Cancel
  • Full Name Full Name Comment goes here.
    Are you sure you want to
    Your message goes here
    Processing…
Post Comment
Edit your comment

    シンプルモデル:トランスモデルのパラメータ及び説明について シンプルモデル:トランスモデルのパラメータ及び説明について Presentation Transcript

    • シンプルモデル:トランスモデルの パラメータ及び説明について 2012年6月13日 株式会社ビー・テクノロジー All Rights Reserved Copyright (C) Bee 1 Technologies Corporation 2012
    • シンプルモデル:トランスモデルのコアモデルのパラメータ(4つ) Model Parameters: BSAT  The saturation flux density (in teslas). – e.g. 100mT, 350mT, 500mTB-H Curve – Value = <BSAT>test points RLOSS  The resistor RLOSS represents a loss when a voltage is applied. – e.g. 0.5Ω, 1Ω, 100KΩ – Value = <RLOSS> LM  Magnetizing inductance of the core inductor (in henry). – e.g. 1uH, 5uH, 50uH – Value = <LM> Figure 1, Saturable core model (Default parameters). BEXP  The exponent in the expression for coupling factor KC. – e.g. 2, 4, 8 – Value = <BEXP> All Rights Reserved Copyright (C) Bee 2 Technologies Corporation 2012
    • シンプルモデル:トランスモデルのトランスモデルのパラメータ(4つ) Parameter settings of 1:1 ideal transformer Model Parameters: LP  Inductance of primary winding (in henry). – e.g. 100uH, 250uH, 500uH – Value = <LP> N  is the turns ratio of Ideal transformer. – e.g. 0.1, 0.5, 1 Figure 2, 1:1 Ideal transformer (Default parameters). – Value = <N> RP  A series resistance of primary winding (in ohm). – e.g. 1mΩ, 10mΩ, 100mΩ – Value = <RP> RS  A series resistance of secondary winding (in ohm). – e.g. 1mΩ, 10mΩ, 100mΩ – Value = <RS> Figure 3, 1:1 Phase reverse ideal transformer (Default parameters). All Rights Reserved Copyright (C) Bee 3 Technologies Corporation 2012
    • シンプルモデル:トランスモデルのトランスモデルのパラメータ(5つ) Parameter settings of 2:1 ideal transformer Model Parameters: LP  Inductance of primary winding (in henry). – e.g. 100uH, 250uH, 500uH – Value = <LP> N  is the turns ratio of Ideal transformer. – e.g. 0.1, 0.5, 1 – Value = <N> RP1  A series resistance of primary winding 1 (in ohm). – e.g. 1mΩ, 10mΩ, 100mΩ – Value = <RP1> RP2  A series resistance of primary winding 2 (in ohm). Figure 4, 2:1 Ideal transformer (Default parameters). – e.g. 1mΩ, 10mΩ, 100mΩ – Value = <RP2> RS  A series resistance of secondary winding (in ohm). – e.g. 1mΩ, 10mΩ, 100mΩ – Value = <RS> All Rights Reserved Copyright (C) Bee 4 Technologies Corporation 2012
    • シンプルモデル:トランスモデルのトランスモデルのパラメータ(5つ) Parameter settings of 1:2 ideal transformer Model Parameters: LP  Inductance of primary winding (in henry). – e.g. 100uH, 250uH, 500uH – Value = <LP> N  is the turns ratio of Ideal transformer. – e.g. 0.1, 0.5, 1 Figure 5, 1:2 Ideal transformer (Default parameters). – Value = <N> RP  A series resistance of primary winding (in ohm). – e.g. 1mΩ, 10mΩ, 100mΩ – Value = <RP> RS1  A series resistance of secondary winding 1 (in ohm). – e.g. 1mΩ, 10mΩ, 100mΩ – Value = <RS1> RS2  A series resistance of secondary winding 2 (in ohm). – e.g. 1mΩ, 10mΩ, 100mΩ – Value = <RS2> Figure 6, 1:2 Center tap ideal transformer (Default parameters). All Rights Reserved Copyright (C) Bee 5 Technologies Corporation 2012