Model dwl600 series heavy duty digital level

551 views
478 views

Published on

0 Comments
0 Likes
Statistics
Notes
  • Be the first to comment

  • Be the first to like this

No Downloads
Views
Total views
551
On SlideShare
0
From Embeds
0
Number of Embeds
10
Actions
Shares
0
Downloads
2
Comments
0
Likes
0
Embeds 0
No embeds

No notes for slide

Model dwl600 series heavy duty digital level

  1. 1. Model DWL600 SeriesThe DWL600 series Electronic Level is designed to be fitted into top qualityJapanese Aluminium Profile structure at 24” length to meet various practicalapplications.Models: Models Special Feature DWL600E  Displayed in degree(° slope (%), mm/M and inch/Feet ),  High quality Japanese Heavy duty corrosion resistant aluminium box level  Inverted Reading. Dimension L(615) x H(48) x T(20) mm for 24” Length DWL600EFeatures & Specification: Application:• Measurement Range 0°~ +/- 90° High Resolution 0.05°~ 0.1°• Operating Temperature 0° ~ 50° C• Long Battery Life with 3 minutes auto off• Easy, Clear & Precise Digital Display• Hold Function to Freeze Display• Buzzer Sound with Build-in Vials High quality White Back Light Power supply 2 x AAA/ 9V Batteries (Batteries included) For further information, please refer to www.digipas.co.uk
  2. 2. Model DWL600 Series CALIBRATION INSTRUCTION OPERATIONCaution: Digi-Pas is calibrated in the Factory for a) Batteries:maximum accuracy. User only recalibrate unless  The battery compartment is inside thenecessary. end of the right hand side of the level.  Remove the end cap and place the new1. Push ONCE on the Cal button then batteries (type AAA/ 9V) in the batteryrelease.Buzzer starts to beep. compartment2a. Place Digi-Pas on a flat surface (e.g. Table)  Ensure correct polarity.Use a finger to Press Mode button ONCE while b) Switching on the Digi-Pas:wait a few seconds until buzzer beeps.  Switch the Digi-Pas on using the on/off b. Place Digi-Pas reverse horizontal (180° Press ) switch.Mode button ONCE and wait a few seconds until  The Digi-Pas can measure angles rangebuzzer beeps. 0°~ +/- 90° c. Place Digi-Pas vertically (-90° and Press )  press mode button to choose theMode button ONCE and wait a few seconds until resolution in degree, slope angle mm/Mbuzzer beeps. and inch/Feet d. Place Digi-Pas reverse vertically (+90° and) c) Buzzer Sound (Acoustic signal):Press Mode button ONCE and wait a few seconds  The Buzzer Sound are used to indicateduntil buzzer beeps. angle of slope stands at 0° 90° and ,3. Calibration completes when buzzer beep when you “HOLD” a specific reading.sound stops.  To switch off Acoustic signal, hold the NOTE : Ensure Digi-pas is kept still during Mode for more than 2 seconds, theCalibration speaker enunciator will be disappeared. d) High quality White Back Light  Enable level working at dark environment e) Hold button (Memory functions)  With the hold button, you can Freeze Display for reading and the current measurement result can be saved in the internal memory.  Return to normal measuring mode by pressing Hold button  To call back the reading in the internal memory, press Hold button for 3 second. The previous save reading will be appearing in the display. f) Switching off:  To switch off the Digi-Pas, press the on/off switch .When not in use more than 3 min, the Digi-Pas will switches off automatically. UK and Europe sales office Tarax Technology Limited First Floor, Office 2, 10 Panmure Street, Dundee, DD1 2BW. e:Info@digipas.co.uk w:www.digipas.co.uk m:(+44)07825041403 For further information, please refer to www.digipas.co.uk

×