Model DWL 200 SeriesThe DWL 200 is a 200 mm length Digital Mini Level. The strong impact resistance ABSplastic material is...
CALIBRATION INSTRUCTIONCaution: Digi-Pas is calibrated in the Factory for    OPERATIONmaximum accuracy. User only recalibr...
Upcoming SlideShare
Loading in …5
×

Model dwl 200 series digital torpedo level- www.DIGIPAS.co.uk

684
-1

Published on

This is an ideal sized compact digital level that also incorporates the bubble. At 8 inches with 0.1 Degree Resolution. It's LCD display is easy to read with measurements in either degrees and percentages. 1 horizontal and 1 vertical vial. Buzzer Sound at 0, 90 and when you hold a reading Hold Function to freeze display on current reading Long Battery Life with 3 minutes auto off. Built in strong magnet base to firmly hold on flat and pipe surfaces

High accuracy of 0.1 degrees at 0° and 90° and 0.2 degrees at all other angles
Switchable display between degrees (°) or slope (%)
Strong magnet on the base enable the level to be fixed on to any magnetic surface
Buzzer sound at 0°
Measurement Range 0° ~ +/- 90° x 4 (360°)

0 Comments
0 Likes
Statistics
Notes
  • Be the first to comment

  • Be the first to like this

No Downloads
Views
Total Views
684
On Slideshare
0
From Embeds
0
Number of Embeds
1
Actions
Shares
0
Downloads
1
Comments
0
Likes
0
Embeds 0
No embeds

No notes for slide

Model dwl 200 series digital torpedo level- www.DIGIPAS.co.uk

  1. 1. Model DWL 200 SeriesThe DWL 200 is a 200 mm length Digital Mini Level. The strong impact resistance ABSplastic material is molded with a tough Aluminium base to form the rugged yet elegantbody structure.Features & Specification: Models Special Feature Displayed in Degrees (° or slope (%) ) DWL 200 Resolution 0.1°• Measurement Range 0° ~ +/- 90° High Resolution 0.05°~ 0.1° DWL 280 Resolution 0.05°~ 0.1°• Operating Temperature 0° ~ 50° C Dimension L(200) x H(42.5) x T(18) mm• Long Battery Life with 3 minutes auto off• Easy, Clear & Precise Digital Display• Hold Function to Freeze Display• Buzzer Sound with Build-in Vials With magnet on the base Power supply 2 x 3v Lithium cell (Batteries included) For further information, please refer to www.digipas.co.uk
  2. 2. CALIBRATION INSTRUCTIONCaution: Digi-Pas is calibrated in the Factory for OPERATIONmaximum accuracy. User only recalibrate unless a) Batteries:necessary.  Open the battery compartment at the rare of the Digi-Pas .1. Push ONCE on the Cal button then  Remove the small plastic from two newrelease.Buzzer starts to beep. batteries (type AAA/LR03).2a. Place Digi-Pas on a flat surface (e.g. Table)  Ensure correct polarity.Use a finger to Press Mode button ONCE while b) Switching on the Digi-Pas:wait a few seconds until buzzer beeps.  Switch the Digi-Pas on using the on/off b. Place Digi-Pas reverse horizontal (180° Press ) switch.Mode button ONCE and wait a few seconds until  The Digi-Pas can measure angles rangebuzzer beeps. 0°~ +/- 90° c. Place Digi-Pas vertically (-90° and Press )  press mode button to choose theMode button ONCE and wait a few seconds until resolution in degree or slope angle (Ifbuzzer beeps. slopes are measured) d. Place Digi-Pas reverse vertically (+90° and ) c) Buzzer Sound (Acoustic signal):Press Mode button ONCE and wait a few seconds  The Buzzer Sound are used to indicateduntil buzzer beeps. angle of slope stands at 0° 45° 90° , , .3. Calibration completes when buzzer beep  To switch off Acoustic signal, hold thesound stops. Mode for more than 2 seconds, the NOTE : Ensure Digi-pas is kept still during speaker enunciator will be disappeared.Calibration d) Magnets on the based  The Digi-Pas can be affixed to any magnetic surface. e) Hold button (Memory functions)  With the hold button, you can Freeze Display for reading and the current measurement result can be saved in the internal memory.  Return to normal measuring mode by pressing Hold button  To call back the reading in the internal memory, press Hold button for 3 second. The previous save reading will be appearing in the display. f) Switching off:  To switch off the Digi-Pas, press the on/off switch .When not in use more than 3 min, the Digi-Pas will switches off automatically. UK and Europe sales office Tarax Technology Limited First Floor, Office 2, 10 Panmure Street, Dundee, DD1 2BW. e:Info@digipas.co.uk w:www.digipas.co.uk m:(+44)07825041403 For further information, please refer to www.digipas.co.uk

×