Field Assembly Optical ConnectorFeatures Field assembly with simple tools Easy and quick assembly without polishing and epoxy Low insertion loss & reflection lossApplications Fiber Optic Telecommunication Optical Fiber Distributer Optical Cable interconnection Fiber Distribution Frame Connector: SC, LC, FC. UPC/APCSpecificationParameter FAOCInsertion Loss Max. < 0.4dB Avg. < 0.3dBReflection Loss > 50 dBOperating Temperature 20 ~ 60 °CStorage Temperature - 40 ~ 80 °C
AFL Fast Connectors (Pre-Polish Connectors)Features Pre-stubbed, factory-polished ferrule No epoxy required Precision mechanical alignment insures low loss Fiber can be reseated 3.0mm, 2.0mm, and 900μm boot provided with each connector VFI can be used to confirm fiber is installed properly Meets TIA/EIA 568A performance requirements Meets TIA/EIA 604 (focis) connector interface requirementsApplications Premise environments Connections at the desk for LAN environments Patch panels Direct equipment termination Fiber to the Subscriber (FTTx) applications Repair/replacement requirements Equipment test leadsSpecificationInsertion Loss: Maximum: 0.5 dB, Average: 0.2 dB (SM), Average: 0.1 dB (MM)Return Loss: Maximum: 45 dB, Average: 56.4 dBOperating Temperature: -40 ~ +75 °C
Fixed Connector AttenuatorFeatures• Wavelength insensitive• Modal noise suppression• Low polarization dependent loss• High laser power enduranceApplications• Telecommunication systems• Cable television networks• Test equipmentSpecificationAttenuation (dB) PC, APC 1~30dB, 1dB IncrementalOperating wavelength (nm) 1310 and 1550Return loss (dB) PC <-50 APC <-60Tolerance on attenuation (dB) 1~10dB <±0.5 >10dB <±1.0Polarization dependent loss (dB) <0.5Operating temperature -40~+75°C
AFL Splice Connect (Mechanical Splice)AFL Telecommunications’ Splice Connect is a mechanical splice that provides an inexpensive,quick alternative to mating fibers. Using V-groove technology, this splice maintains physicalcontact between the fibers. An assembly tool is used to ensure the fibers are mated correctly,resulting in <0.1dB insertion loss (typical for single-mode).The Splice Connect secures both fiber and coating independently with the U-shaped sleeve,enhancing the strength against fiber twist.Features• Quick splicing time• Minimal tools• 250μm and/or 900μm fiber capabilities• Both fiber and coating are secured independently.Applications• Restoration• Premise environments• Fiber-to-the-Subscriber (FTTx) applications
PLC SplitterDescription The planar light wave circuit (PLC) splitter is wave guide device based on substrates ofquartz, silicon or other materials, which is used for power coupling and reallocation of opticalsignals. It features low wavelength sensitivity, small size, high reliability, per fed splittinguniformity. Wide wavelength range, and so on, and is especially applicable to OLT and ONTconnection and splitting of optical signals over FTTX passive optical networks. Features Perfect splitting uniformity Small polarization dependent loss High reliability and better fail failure mode Small size, compact structure ,easy integration Multi-channel. Large cost reduction space, facilitating batch production.
Outdoor FTB 2/4 fiber (TN-4FFTTH)DescrabtionThe FTB 2/4 from TENAS Factory is rugged. low profile interconnection between central officeand multi-dwelling units of FTTx applicationThe design of FTB 2/4 splitter terminal combines the functionality of a local convergencecabinet with FTB 2/4Is multi-layer design allows installers to access only the components necessary for initialinstallation or subscriber turn-up. It can house the splitter and allows for pigtail splicing ofdistribution drop cables as needed.Features • Indoor or outdoor rated. • You can use 1x2, 1x4, 2x4 and 1x8 splitter. • Max. up 8 pcs of FTTH drop cable or pigtails. • Suitable for Wall-mounting or pole mounting application • 2pcs of inlet ports and 8x2 pcs of outlet ports • You can use LC or SC connectors • Dust and splash-proof: IP65Application • FTTH, FTTB, FTTC. • Telecommunication network. • CATV.
Outdoor FTB 12/24 fiber (TN – 24 FTTH)DescrabtionThe FTB 12/24 from TENAS Factory is rugged. Low profile interconnection between centraloffice and multi-dwelling units of FTTx applicationThe design of FTB 12/24 splitter terminal combines the functionality of a local convergencecabinet with FTB 12/24Is multi-layer design allows installers to access only the components necessary for initialinstallation or subscriber turn-up. It can house the splitter and allows for pigtail splicing ofdistribution drop cables as needed.Features • Indoor or outdoor rated. • You can use 1x4, 1x8, 1x16 splitter as well as 2x4,2x8,2x16 splitter. • Max. up 32 pcs of FTTH drop cable or pigtails. • Suitable for Wall-mounting or pole mounting application • 2pcs of inlet ports and 8x2 pcs of outlet ports • You can use LC or SC connectors • Dust and splash-proof: IP65Application • FTTH, FTTB, FTTC. • Telecommunication network. • CATV.
ODB Indoor typesDescriptionThe fiber distribution box is applicable to optical terminals. It completes the connection,distribution and scheduling between subscriber cable and optical fiber terminals and is widelyapplied to optical fiber communication network projects.The product series are wall-mounted and easy to use and maintain.features Used in indoor. Dust and splash-proof: IP55 Wall-mounted or pole-mounted, Single door, front operation Made of high quality steel sheet, spraying for surface treatment Applicable to pigtails 0.9mm; length: 0.5--1m Available in FC, LC and SC connector Protection and grounding Perfect optical route design to ensure good bend radius of fiber Indoor ODB 12 Fiber
ODF Optical Distribution FrameDescriptionODF is a modular encapsulation of Optical Splitters in a rack mountable unit, with a patch panel forinput and output adapters.features Rack-mount, 19 inch (483mm) & ETSI rack. Adjustable Distance (0/30mm) between installations. Ear or guide ring plate and unit front cover. Made of high-quality steel sheet, surface. Electrostatic spray, pleasant appearance. We can supply 24,48,72,96 and 144 fiber
Optical Splitter Box (OSB)DescriptionOptical Splitter Box from TENAS Factory is passive opticaldevice that divides one input of optical power intotwo or more outputs.features Used in indoor Wall mounted, Single door, front facing operation Material: high quality steel sheet, spraying for surface treatment Optional various optical splitters Compatible with PLC and PBT optical splitters Applicable to pigtails of splitter: 0.9mm; length: 0.5--1m Available in LC & simplex. Plug-in inlet optical cable We can supply with PLC splitter 1x16 and 1x32
Optical Splitter Frame (OSF)DescriptionOptical Splitter Frame from TENAS Factory is passive optical device that dividesone input of optical power into two or more outputs.OSF, 4 x 1:2, LC/APC connectorOSF, 4 x 1:4, LC/APC connectorOSF, 1:32, LC/APC connectorOSF 16 x 1:2, LC/APC connectorOSF, 8 x 1:2, LC/APC connectorOSF, 2:32, LC/APC connector
Fiber Optic SocketOVERVIEWIt is the final project of FTTH access. It provides solutions to ONT (or home gateway)installation, inlet of indoor optical cables and indoor cabling. The project involves products suchas the household information box , field connector and mechanical splice used for connectionof single-fiber drop cables, and patch cord. When the ONT (or home gateway) needs to beinstalled in a box, the household information box is adopted usually. When the ONT (or homegateway) needs to be installed on the desktop, the fiber socket is adopted usually.Socket-outletFeatures Independent use. Quality polycarbonate (PC) material, with perfect fireproof performance. Allowing storage of a small quantity of redundant fibers.Face PlateFeatures Independent use. Quality polycarbonate (PC) material, with perfect fireproof performance. SC simplex or LC duplex ,
Fiber Optic ClosureDescriptionFiber Optic Closure from TENAS Factory is specialized designed for FTTx application.The product adopts Heat shrinkable sleeve, it can be used for straight-throughand branching-off application, as well as passive Optical fiber distribution. GJS-01-12- 72 Fiber Optic ClosureApplication FTTH,FTTB,FTTC Telecommunication Network CATV Local Area Network GJS03A- 96—1 Fiber Optic ClosureDescriptionThe GJS03A-96-1 from TENAS Factoryis specialized designed for FTTx application.The product adopts Heat shrinkable sleeve,it can be used for straight-throughand branching-off application, as well as passiveOptical fiber distribution.
SpecificationHeight: 53cm, Net Weight: 1.64kg,Base diameter: 16cm, closet ring dia.:21cm4 small holes +1 oval holeThe diameter of the small holes is 2.0cm.The major axis of the oval hole(inside wall)is 6.cm,and the shorter axis of the oval hole is 4.cm.Application FTTH,FTTB,FTTC Telecommunication Network CATV Local Area Network GJS03S- JF144--1 Fiber Optic ClosureDescriptionThe GJS03S-JF144-1 from TENAS Factoryis specialized designed for FTTx application.The product adopts Heat shrinkable sleeve,it can be used for straight-throughand branching-off application, as well as passiveoptical fiber distribution.SpecificationWeight: 1.78kg Height: 42cmBase diameter:16cm , closet ring dia. :21cm4 small holes +1 oval holeThe diameter of the small holes is 2.0cm.The major axis of the oval hole(inside wall)is 6.cm,and the shorter axis of the oval hole is 4.cm.Application FTTH,FTTB,FTTC Telecommunication Network CATV Local Area Network
GJS03F-JF192Fiber Optic ClosureDescriptionThe GJS03D-JF96 from TENAS Factoryis specialized designed for FTTx application.The product adopts Heat shrinkable sleeve,it can be used for straight-through and branching-off application,as well as passive Optical fiber distributionSpecificationWeight: 1.85kg, Height: 53cmBase diameter: 16cm, closet ring dia.:21cm4 small holes +1 oval holeThe diameter of the small holes is 2.0cm.The major axis of the oval hole (inside wall)is 6.cm,and the shorter axis of the oval hole is 4.cm.Application FTTH,FTTB,FTTC Telecommunication Network CATV Local Area Network GJS03E-288Fiber Optic ClosureDescriptionThe GJS03E-288 from TENAS Factoryis specialized designed for FTTx application.The product adopts Heat shrinkable sleeve,it can be used for straight-throughand branching-off application, as well as passiveoptical fiber distribution.
SpecificationHeight: 71cm Weight:7.4kgBase diameter:28cm closet ringdia.:29.6cm5 small holes +1 oval holeThe diameter of the small holes is 3.3 cm.The oval hole is the same as GJS03AApplication FTTH,FTTB,FTTC Telecommunication Network CATV Local Area Network GPJ-04V7 Fiber Optic Splice Closure For FAT and BF-FAT GPJ-04V7
Features Nonmetal case to effectively prevent condensation One and Double door operation on one side Available in splicing &termination tray Lead-in cable trays by areas after cable fixed –stripping –protection Available in duplex LC adapter
Small Form-Factor Pluggable (SFP) TransceiverDescriptionSmall Form-Factor Pluggable (SFP) is a compact, hot-pluggable transceiver used for bothtelecommunication and data communication application. It interfaces network device motherboard (for a switch, router, media converter or similar device) to fiber optic or coppernetworking cable. It is a popular industry format supported by many network componentvendors.SFP transceivers are designed to support SONET, Gigabit Ethernet, Fiber Channel, and othercommunication standards. The standard is expanding to SFP+ which will be able to supportdata rates up to 10.0Gbit/s (that will include the data rates for 8gigabit Fiber channel, and10GbE). SFP+ module versions for optical as well as copper are being introduced. In comparisonto Xenpak, X2 or XFP type of modules, SFP+ module leave some of the circuitry to beimplemented on the host board instead of inside the module.
Media converter types 1. 10/100/1000Base-SX/LX SmartApplicationThe planet GST-80x provides advanced Media conversion technology- 10/100/1000Base-T andSX/LX interfaces to fulfill different kinds of demand as the current network grows andexpanding. The GST-80x provides diverse fiber connect type options for different networkapplications. It is very flexible for the GST-80x working as a standalone device or being installedin the central Web Smart/Management media converter chassis for centralized management.When working with the Web Smart/Management media converter chassis the GST-80x is hotswappable to avoid network downtime. The GST-80 is the ideal solution for building a networksolution of FTTH or FTTC and FTTB for ISPs, campuses and enterprise. 2. 10/100Base-TX to 100Base-FX Smart
3. 10/100Base-T to 100Base-SX/LX GigabitApplicationWith high performance of data transmission and easy installation, the GT-80x can build the ISPnetwork solution of FTTH or FTTC and FTTB, also for small office network environment ofenterprises. 4. Managed Gigabit Ethernet
FURUKAWA Splicer Machine S178A Features Rugged and compact hand held design to endure any kind of environmental conditions Fast splice (7 sec) at super low loss and Fast Heating (25 sec)*1200 cycles (Splicing & Heating) with 2 batteries Available for All METRO/LAN/FTTx fibers including ultra bend-insensitive fibers (e.g.EZ-Bend™) Applicable for Splice-on-connector(SOC) – Both Seiko Galen Connectors and Diamond Connectors available Easy maintenance – Easy electrode replacement /mirror free alignment system Auto-start shrink sleeve oven feature Improved GUI to further enhance ease-of-use Large memory for storing data(2,000 splice data) and image(100 images) RoHS and Telcordia (GR-765-Core) compliantSpecificationApplicable fibers SMF, MMF, DSF, NZDSF, BIF/UBIF(Bend insensitive fiber)Fibers cleave length 5 - 16 mm for 250 um fiber, 10 -16 mm for 900um tight bufferCladding Diameter 80 -150umCoating Diameter 160 - 900umTypical Insertion Loss 0.02dB for SMF, 0.01dB for MMF( similar fiber splicing) 0.03dB for NZDSF, 0.04dB for EZ-BendSplice Programs Up to 150Automatic splicing selection SM: SMF, DSF, NZDSF, BIF/UBIF(Bend insensitive fiber) MM: MMFHeat Program Up to 18Auto heating start availableDimension 127W x 199D x 105H mm (Not including shock absorber) 159W x 231D x 130 H mm (Including shock absorber)Fiber Holding Tight Holder (Loose tube applicable)
or Fiber Holder SystemWeight 1.9 kg (without battery), 2.3kg (with two batteries)Splice time 7 seconds (Semi-auto mode), 9 seconds (Regular mode)Applicable Sleeves 40/60mmHeating time 25 seconds for 40mm and 60 mm sleeves 31 seconds for 40mm and 60 mm sleeves (Regular mode)Return loss >60dBTension Test 1.96 NMagnification 101x, 304x or 608xMonitor 3.5" color LCD monitorVideo output/Data interface USB 2.0Splice memory maximum 2000 splicesImage capture capacity Last 100 images to be automatically captured + Up to 24Display user interface GUIBattery capacity 80 splice/heat cycles with single battery 200 splice/heat cycle with dual batteriesDisplaying language 20 languages (e.g. English, Spanish, Japanese, Chinese)Operating temperature -10 to + 50 degree C (without excessive humidity)Storage temperature -40 to +60 degree C (without excessive humidity)Power source AC 100 to 240V (50/60Hz), DC Input 11 to 17 VWorktable Available
FURUKAWA Fiber Optic Cleaver S325AFeatures One-Step Action Cleave Anywhere! - In Your Palm or on Your Desktop Easy Fiber Loading Simple Operation High Capacity Waste Fiber Collection Durable Design Easy Maintenance on-SiteSpecificationsFiber Types All fiber types, single to 12-fiber ribbonsClad Diameter 0.125mmDimensions/Weight 93W x 68D x 52H [mm], 330 grams Ribbon Fiber: 10mm Fixed LengthCoating Diameter 0.25mm and 0.9mm for single fiberCleave Length Single Fiber: Fixed Length - 10 & 16mm Variable Length - 3 to 20mm
Fiber Optic Test Equipment1- OPTICAL TIME DOMAIN REFLECTOMETERS (OTDRs) AND FAULT LOCATORS:OTDR from AFL with deferent models for SM or MM applications to meet all fiber optic requirements toperform all loss measurements and fault location.AFL recently produced allots of products For FTTxProjects like OFL280 with two deferent models to perform the construction and maintenance for FTTxnetworks also this device is integrated with power meter & light source & VFL2- OPTICAL LOSS TEST KITS:Power meter and light source test kit from AFL for SM or MM applications to measure total losses overthe link and optical power.AFL provides deferent models depending on fiber applications.
3- OPTICAL FIBER IDENTIFIERS:Optical Fiber Identifier from AFL designed to identify the presence or absence of fiber optic signal and todefine direction of traffic and tone detection.AFL produced OFI-FTTx to identify the presence or absence of an active Optical Network Terminal (ONT)Thus the OFI-FTTx can verify whether a splitter pigtail at the FDH is connected to an active circuit beforeit is disconnected for fault location or re-use.4- INSPECTION MICROSCOPES AND VIDEOSCOPES:Optical Fiber Scope from AFL is used for inspection of optical fiber connectors for scratches, dirt, or otherproblems normally associated with poor transmission performance.
5- FIBER OPTIC TALK SETSFTS1 & FTS 2 Fiber Optic Talk Sets are designed for voice communication over spare fibers, and providefull duplex, hands-free operation.The FTS-20C, a clip-on coupler, is available for bare fiber access where terminated ends are not available.6- VISUAL FAULT IDENTIFIER & LOCATOR (VFL)The HiLite and VFI 2 are compact but powerful visible red laser sources designed to identify faults in fiberoptic jumper cables, distribution frames, patch panels, and splice trays.
7- VARIABLE FIBER OPTIC ATTENUATORSProvide technicians with a controlled means of attenuating or adjusting an optical signal level down fromthe transmitted level. Applications include field and laboratory testing of system performance over arange of attenuation values (network loads) and tuning and verifying performance of new transmittersto specific networks at time of installation. AFL offers a range of attenuators providing test options totechnicians.8- QUAD OTDR and CERTICIATION TEST KITThe Noyes C860 QUAD Certification and OTDR Test Kit from AFL Telecommunications includes onehandheld C840 QUAD OLTS Tester and one C850 QUAD OTDR/OLTS with built-in auto test functionality.With this kit, technicians can troubleshoot and perform both Tier 1 and Tier 2 certification tests of MMand SM fiber networks, store results and create professional test reports.
9- FIBER OPTIC LOSS & TEST SETThe OLTS 5 Optical Loss Test Set series offers end-to-end single-mode testing at either 1310/1550 nm(OLTS 5-3 model) or 1550/1625 nm (OLTS 5-5 model).10- FIBER OPTIC LOSS & RETURN LOSS TEST SETThe NOYES TURBOTEST 500B from AFL offers a single-mode bi-directional test solution for measuringboth optical loss and return loss. Five compact models are available featuring dual and triple wavelengthcombinations. An optional digital full-duplex talk set option is available
• Compact fan-less Gigabit Ethernet switch with integrated power supply• Integrated management with web-, SNMP,- and Telnet-interface• 8x 10/100/1000Base-T, 2x SFP uplink-slots• Data prioritization according to IEEE802.3p/Q, VLAN support• 802.1x port-based network access control (Authentication)• STP/RSTP according to IEEE802.1d & 802.1w• IGMP-Snooping, bandwidth management, port mirroringFast Ethernet Installation SwitchOptimised compact and fanless design• Ports• 1x 100Base-FX fiber uplink• 4x 10/100Base-TX Twisted Pair RJ-45 ports• 1x 10/100Base-TX Twisted Pair RJ-45 downlink (optional)• Power-over-Ethernet functionality on all RJ-45 ports (optional)• Integrated network management (optional)
Fast Ethernet Bridging Converter 10/100Base-T/100Base-FXThe Bridging Converter offers easy and cost effective media conversion from fiber opticto copper in Fast Ethernet networks. This product family is specially designed tominimize costs.A special feature is the possibility to configure the Bridge in Converter mode forapplications with low latency requirements.• Compact and cost effective design• Robust metal housing• Bridging (10/100) or Converter Mode (100)• Multimode max. 2 km, Single ModeFast and Gigabit Ethernet Bridging Converter• Fast Ethernet and Gigabit Ethernet converter• Auto negotiation for speed and duplex mode• Copper port supports auto MDI/MDIX• Link Through function integrated• SFP-slot for 1000Base-XGigabit Ethernet 8 Port Desktop SwitchWith the 8 port Gigabit Ethernet switch, MICROSENS offers an universal device forprofessional use in small, Medium and large networks. Based on the comprehensiveManagement functionality with Web, CLI and SNMP access, the device satisfies alldemands.The Gigabit Ethernet Switch is flexible and offers the best solution for creating and expandingyour networks. It has an integrated power supply unit and is fan-less. Additionally, the switchoffers an unbeatable price/performance ratio.