9400 9600 programming

277 views
207 views

Published on

0 Comments
0 Likes
Statistics
Notes
  • Be the first to comment

  • Be the first to like this

No Downloads
Views
Total views
277
On SlideShare
0
From Embeds
0
Number of Embeds
1
Actions
Shares
0
Downloads
1
Comments
0
Likes
0
Embeds 0
No embeds

No notes for slide

9400 9600 programming

  1. 1. HT-2 / 9600 Series Instructions Spaside ControlProgram Key Time of Day: “CL” will appear in the LCD window. Set any time from 00:00 to 23:59. Filtration Cycle Start Time: “FIon” will appear in the LCD window. Set time from 00:00 to 11:59. Filtration Duration: “ FIdu” will appear in the LCD window. Set duration from Off (no filtration) to 12:00 (continuous filtration). Economy Start Time: “ECon” will appear in the LCD window. Set any time from 00:00 to 23:59. Economy Duration: “ECdu” will appear in the LCD window. Set any hour from Off to 24:00 (always on). Temperature in F° or C°: “Tu” will appear in the LCD window. Set either F or C. Spa-Side Lock: “Loc” will appear in the LCD window. Set to either On or Off. While the Spa-Side is locked you will not be able to change the programming, adjust the Set Point temperature or change the Economy Mode. This mode is a helpful when small children are using the spa. http://www.MyPoolSpas.com Wholesale Pool and Spa Parts 920-925-3094
  2. 2. HT-2 / 9600 Series Programming Low Level ProgrammingIt is possible to change the parameters of the Equipment System by positioning specific jumperslocated on the system board.To enter the Low Level Programming press and hold the Program Key for 20 seconds until thefirst programming parameter appears, which is P1 for Pump 1. Use Up and Down Arrow Keys toincrease or decrease the programming value. Press the Light Key to continue through eachprogramming parameter using the Up and Down Arrow Keys to set the value. You mustcontinue through all parameters to exit this mode.P1 (Pump 1) Value 1 – Single Speed Value 2 – Dual SpeedP2 (Pump 1) Value 0 – No Second Pump Value 1 – Single Speed Value 2 – Dual SpeedbL (Blower) Value 0 – No Air Blower Value 1 – Single Speed / 20 minute timeout Value 2 – Two Speed / 20 min. timeout Value 3 – Three Speed / 20 min. timeout Value 4 – Single Speed / 2-hour timeout Value 5 – Single Speed / 6-hour timeout Value 6 – Single Speed / 12-hour timeoutL1 (Light) Value 0 – No Light Value 1 – 12VAC Single Intensity Value 2 – 12VAC Three Intensities Value 3 – 120VAC LightO3 (Ozone) Value 0 – No Ozone Value 1 – On during filtration only Value 2 – Always OnAU (Fiber Optic) Value 0 – No Fiber Optics Value 1 – Fiber Optics InstalledTi (Time) Value 12 – Standard Clock Value 24 – 24-hour (military clock)Cu (Current) Value 0 – No Heat with High Speed Pump or Blower (120VAC) Value 1 – No Current Restriction (240VAC)Cp (Circ. Pump) Value 0 – No Circulation Pump Value 1 – Regulated with Spa Temperature Value 2 – Always Onr (Sensor Calibration) Value can be adjusted from 46.0 to 55.9 (this number is marked on the temperature sensor and is programmed at the factory). http://www.MyPoolSpas.com Wholesale Pool and Spa Parts 920-925-3094

×