Tdm & fdm

9,786 views
8,938 views

Published on

1 Comment
5 Likes
Statistics
Notes
  • #FDM - FDMEE Hyperion Financial Data Management Enterprise Edition Oracle FDM FDMEE Hyperion Data Management Videos and Books Online Sharing $14 9GB http://www.dbmanagement.info/Tutorials/FDM.htm
       Reply 
    Are you sure you want to  Yes  No
    Your message goes here
No Downloads
Views
Total views
9,786
On SlideShare
0
From Embeds
0
Number of Embeds
10
Actions
Shares
0
Downloads
329
Comments
1
Likes
5
Embeds 0
No embeds

No notes for slide

Tdm & fdm

  1. 1. e d h e as R i r 03 A N za E- LT U P U d C M a - m 09 ZU a m 20 B u h T M E & UC 1McGraw-Hill ©The McGraw-Hill Companies, Inc., 2000
  2. 2. NoteBandwidth utilization is the wise use of available bandwidth to achieve specific goals. Efficiency can be achieved by multiplexing; i.e., sharing of the bandwidth between multiple users. 6.2
  3. 3. 6-1 MULTIPLEXING Whenever the bandwidth of a medium linking two devices is greater than the bandwidth needs of the devices, the link can be shared. Multiplexing is the set of techniques that allows the (simultaneous) transmission of multiple signals across a single data link. As data and telecommunications use increases, so does traffic.Topics discussed in this section: Frequency-Division Multiplexing Synchronous Time-Division Multiplexing 6.3
  4. 4. Figure 6.1 Dividing a link into channels 6.4
  5. 5. NoteFDM is an analog multiplexing technique that combines analog signals. It uses the concept of modulation 6.5
  6. 6. Figure 6.4 FDM process 6.6
  7. 7. Figure 6.5 FDM demultiplexing example 6.7
  8. 8. Figure 6.12 Time Division Multiplexing (TDM) 6.8
  9. 9. NoteTDM is a digital multiplexing techniquefor combining several low-rate digital channels into one high-rate one. 6.9
  10. 10. Figure 6.13 Synchronous time-division multiplexing 6. 10
  11. 11. INTERLEAVINGThe process of taking a group of bits from each input line for multiplexing is called interleaving . 6.11
  12. 12. Figure 6.15 Interleaving 6. 12
  13. 13. FREQUENCY DIVISION MULTIPLEXSeparation of spectrum into smallerfrequency bandsChannel gets band of the spectrum for the Channels kiwhole timeAdvantages: k 3 k 4 k5 k6 no dynamic coordination needed works also for analog signalsDisadvantages: waste of bandwidth if traffic distributed unevenly inflexible guard spaces t
  14. 14. 6.15
  15. 15. WHY FDM IS FOR ANALOG SIGNALS AND TDM IS FOR DIGITAL SIGNALS?FDM stnds for frequency divisionmultiplexing and it is used only in case ofanalog signals because analog signals arecontinuous in nature and the signal havefrequency.TDM-stands for time division multiplexingand it is used only in case of digitalsignals because digital signals arediscrete in nature and are in the form of 0and 1s. and are time dependent. 6.16
  16. 16. ADVANTAGES & DISADVANTAGES OF TDM & FDMIn TDM, different users share the same channel based ontime slots alloted to them. Each user or source is given aparticular time slot to send its information.1. The entire channel BW is available for a particular timeinterval unlike in FDM where the channel BW is split intosmaller segments. This enables higher data rates.2. All users share the same frequency, so spectrumefficieny is increased. Available channel BW is no more aconstraint. 6.17
  17. 17. 18McGraw-Hill ©The McGraw-Hill Companies, Inc., 2000

×