Ld5500 Install Guide
Upcoming SlideShare
Loading in...5
×

Like this? Share it with your network

Share

Ld5500 Install Guide

  • 1,625 views
Uploaded on

If you've owned a regular radar detector, you know the hassles of setting it up and hiding it from thieves when not in use. You hate the dangling cords, suction cups and Velcro tabs that destroy......

If you've owned a regular radar detector, you know the hassles of setting it up and hiding it from thieves when not in use. You hate the dangling cords, suction cups and Velcro tabs that destroy the elegant contours of your instrument panel.

K40's exclusive "Divide-and-conquer" concept solves all that. Inside the cockpit, separate alert lights and speakers or custom Warning Pod mounts invisibly into your vehicle's instrument cluster. A unique two piece control switch, installed discreetly under the kick panel or in the dash, adjusts the on/off, city/highway, and volume functions.

More in: Automotive , Technology
  • Full Name Full Name Comment goes here.
    Are you sure you want to
    Your message goes here
    Be the first to comment
    Be the first to like this
No Downloads

Views

Total Views
1,625
On Slideshare
1,625
From Embeds
0
Number of Embeds
0

Actions

Shares
Downloads
0
Comments
0
Likes
0

Embeds 0

No embeds

Report content

Flagged as inappropriate Flag as inappropriate
Flag as inappropriate

Select your reason for flagging this presentation as inappropriate.

Cancel
    No notes for slide

Transcript

  • 1. ELECTRONICS TM LASER DEFUSERPLUS INSTALLATION INSTRUCTIONS PARTS KIT Parts Kit includes the following: A A- (1) Universal Mounting Bracket B- (1) Red L.E.D. Laser Alert Light B C C- (1) Piezo Beeper w/ “O” Ring Tape D- (1) Double Stick Tape Strip E- (2) 36” - 20 ga. Grounding/Power Wires D F- (1) 3 AMP Fuse Assembly G- (4) Barrel Connectors E F H- (2) 1” - 1/4” x 20 Nylon Bolts I- (2) 1 1/2” - 1/4” x 20 Nylon Nuts J- (8) 1/4” x 20 Nylon Bolts K- (2) #6 x 1/4” Screws G H I L- (3) #10 x 3/4” Screws M- (1) 1/2” Self Tapping Screw J K L M N N- (1) 22-16 ga. Ring Terminal IMPORTANT - PLEASE READ BEFORE INSTALLING When installing the Laser DefuserPlus outside of the system’s license plate frame, the unit should be mounted as close to the center of the vehicle as possible, without obstruction. The mounting location of the Laser DefuserPlus is important, as police laser gun operators are trained to aim for the flat, reflective surface of a targeted vehicle’s front license plate. In states that do not require a front license plate, operators will traditionally aim for the front, center of the vehicle. This procedure allows the operator to effectively "bounce" the laser signal back to the gun to calculate the vehicle’s speed.
  • 2. Note: When integrating the Laser DefuserPlus with the K40 remote radar system, the Laser DefuserPlus will utilize the same warning light/speaker(s) as the K40 remote. Therefore, you will not need to install the red L.E.D. alert light or piezo beeper that come with the Laser DefuserPlus. LASER L.E.D. LIGHT 1. For best visibility, choose a mounting location for the laser L.E.D. as close to the vehicle gauges as possible. See diagram A1. 2. Check for proper clearance behind the area where the L.E.D. will be installed (approximately 1”), and drill a 3/16” hole in the chosen location. See diagram A2. 3. Route the L.E.D. wires under the dash per diagram A3 and connect according to the appropriate block diagram. DIAGRAM A1 ALERT LIGHT 1" RED ALERT L.E.D. GREY L.E.D. BLACK L.E.D. WIRE WIRE DIAGRAM A2 DIAGRAM A3 PIEZO LEFT AIR BEEPER PIEZO BEEPER VENT 1. For maximum audio output and concealment, mount the piezo beeper in the driver’s left air vent. See diagram B1. 2. Use the supplied double stick “O” ring tape to mount the piezo beeper. 3. Route the piezo beeper wires through or under the dash per diagram B1 and connect according to the appropriate RE D block diagram. WI RE BLACK WIRE DIAGRAM B1 FRONT LASER DEFUSERPLUS LICENSE PLATE MOUNT 1. Remove the mounting bolts and any existing frame or cover from the license plate. Remove license plate. See diagram C1. FACTORY LICENSE PLATE BOLTS DIAGRAM C1
  • 3. 2. Position the Laser DefuserPlus around the existing front license Note: For optimum per- plate and mount it against the factory license plate bracket. formance, the DefuserPlus Use the existing mounting bolts or K40 nylon bolts to secure the must be mounted parallel to DefuserPlus frame and license plate to the bracket. the ground. Use the supplied K40 See diagram C2. nylon nuts and bolts to correct the mounting angle of the DefuserPlus DEFUSERPLUS either up or down as needed. On some vehicles, it may be necessary BOLTS to adjust or reposition the factory FACTORY MOUNTING license plate bracket to achieve the LOCATION parallel mounting. On vehicles that have only one set of bracket mounting holes, it is recom- mended that the Laser DefuserPlus LICENSE PLATE and the license plate be bolted together to eliminate any vibration. LASER DEFUSERPLUS LICENSE PLATE MOUNTING NUTS Caution: Avoid hot or moving parts. DIAGRAM C2 3. Route the black and clear zip cord wires into the engine compartment either through the grill or under the bumper. See diagram C3. 4. Pass both the black and clear zip cord wires towards the vehicle’s firewall and through an existing rubber grommet into the vehicle’s interior. See diagram C4. 5. Connect wires according to the appropriate block diagram and insert the 3 amp fuse into the fuse holder. Secure the watertight fuse cover. Turn on the ignition key to verify operation. TO VEHICLE THROUGH INTERIOR FIREWALL CLE AR BLA CK RUBBER GROMMET CLEAR BLACK DIAGRAM C3 DIAGRAM C4 UNIVERSAL MOUNTING BRACKET 1. Choose a mounting location inside the lower air intake vent or grill that has a clear, unobstructed view of the road. DEFUSERPLUS 2. Separate the Laser DefuserPlus module from the license plate MODULE frame by removing the two screws on the backside of the SCREW DEFUSERPLUS frame. See diagram D1. FRAME DIAGRAM D1
  • 4. 3. Determine which holes on the universal mounting brack- et will be used to mount the Laser DefuserPlus to the car. Remove the unused mounting holes on the bracket as needed. See diagram D2. DIAGRAM D2 4. Apply the supplied double stick tape directly to the Laser DefuserPlus and position the DefuserPlus to the universal mounting bracket with the included 1/4” screws. See diagram D3. BRACKET BRACKET TAPE TAPE DEFUSER DEFUSER WITHOUT WITH HORIZONTAL HORIZONTAL TABS TABS 1/4” SCREW 1/4” SCREW DIAGRAM D3 5. Install the Laser DefuserPlus to the desired mounting surface using included 3/4” screws or nylon mounting nuts and bolts. See diagram D4. For optimum performance, make sure DefuserPlus is mounted parallel to the ground as close to the center of the vehicle as possible. See diagram D5. WITHOUT WITH HORIZONTAL HORIZONTAL TABS TABS DIAGRAM D4 INCORRECT INCORRECT CORRECT DIAGRAM D5
  • 5. 6. Route the black and clear zip cord wires into the engine compartment either through the grill or under the bumper. See diagram D6. 7. Pass both the black and clear zip cord wires towards the vehicle’s firewall and through an existing rubber grommet into the vehicle’s cockpit. See diagram D7. 8. Connect wires according to the appropriate block diagram and insert the 3amp fuse into the fuse holder. Secure the watertight fuse cover. Turn on the ignition key to verify operation. THROUGH TO VEHICLE FIREWALL INTERIOR CLE AR BLA CK RUBBER CLEAR BLACK GROMMET DIAGRAM D7 DIAGRAM D6 Note: For optimum per- REAR LASER DEFUSERPLUS formance, the DefuserPlus must be mounted parallel to LICENSE PLATE MOUNT the ground. Use the supplied K40 nylon nuts and bolts to correct the 1. Remove the mounting bolts and any existing frame or cover mounting angle of the DefuserPlus from the rear license plate. Remove license plate. either up or down as needed. See diagram E1. On some vehicles, it may be necessary to adjust or reposition the factory 2. Position the Laser DefuserPlus around the existing rear license license plate bracket to achieve the plate and mount it against the factory license plate bracket. parallel mounting. Use the existing mounting bolts or K40 nylon bolts to secure On vehicles that have only one set of the DefuserPlus frame and license plate to the bracket. bracket mounting holes, it is recom- See diagram E2. mended that the Laser DefuserPlus and the license plate be bolted together to eliminate any vibration. DEFUSERPLUS BOLTS FACTORY LICENSE FACTORY PLATE BOLTS MOUNTING LOCATION LICENSE PLATE LASER DEFUSERPLUS MOUNTING NUTS LICENSE PLATE DIAGRAM E1 DIAGRAM E2
  • 6. 3. Route the black and clear zip cord wires into the trunk, through the passenger compartment, along the driver’s side, and under the dash per diagram E3. 4. Connect wires according to the appropriate block diagram and insert the 3amp fuse into the fuse holder. Secure the watertight fuse cover. Turn on the ignition key to verify operation. TO L.E.D. LIGHT AND PIEZO BEEPER DEFUSER DIAGRAM E3 UNIVERSAL MOUNTING BRACKET 1. Remove the mounting bolts and any existing frame or cover from the rear license plate. Remove license plate. See diagram F1. 2. Separate the Laser DefuserPlus module from the license plate frame by removing the two screws on the back- side of the frame. See diagram F2. FACTORY LICENSE PLATE BOLTS DEFUSERPLUS MODULE SCREW DEFUSERPLUS FRAME DIAGRAM F1 DIAGRAM F2 3. Remove the 3 unused horizontal mounting tabs from the top of the universal mounting bracket. See diagram F3. 4. Apply the supplied double stick tape directly to the Laser DefuserPlus and position the Laser DefuserPlus to the universal mounting bracket with the included 1/4” screws. See diagram F4. BRACKET TAPE DEFUSER WITHOUT 1/4” SCREW HORIZONTAL TABS DIAGRAM F3 DIAGRAM F4
  • 7. 5. Position the Laser DefuserPlus against the license plate and mount it to the factory license plate bracket using the existing mounting bolts or K40 nylon bolts. See diagram F5. 6. Route the black and clear zip cord wires into the trunk, though the passenger compartment, along the driver’s side and under the dash per diagram F6. 7. Connect wires according to the appropriate block diagram and insert the 3amp fuse into the fuse holder. Secure the watertight fuse cover. Turn on the ignition key to verify operation. DIAGRAM F5 TO L.E.D. LIGHT AND PIEZO BEEPER DEFUSER DIAGRAM F6
  • 8. LASER DEFUSERPLUS BLOCK DIAGRAM BLACK ZIP CORD LASER DEFUSERPLUS FUSE CONNECTION COPPER 3AMP CLEAR ZIP CORD +12V IGNITION ON COPPER SILVER CHASSIS SILVER GROUND GREY BLACK RED PIEZO BEEPER BLACK TO +12 VOLT IGNITION ON FUSED SOURCE LASER ALERT L.E.D. Note: When installing front and rear Laser DefuserPlus units, use a separate 3amp fuse for each Laser Defuser. LASER DEFUSERPLUS/K40 REMOTE RADAR SYSTEM INTEGRATION DIAGRAM BLACK ZIP CORD LASER DEFUSERPLUS FUSE CONNECTION COPPER 3AMP CLEAR ZIP CORD +12V IGNITION ON COPPER SILVER SILVER CHASSIS (NOT USED) GROUND K40 REMOTE RADAR VOLUME CONTROL MODULE YELLOW Note: When integrating front and rear Laser DefuserPlus units, both of the clear/copper wires from the two units can be directly connected to the yellow volume control module wire from the K40 remote Radar Detector. ELECTRONICS TM 44533 3/02