Calibre Wiring Guide
Upcoming SlideShare
Loading in...5
×
 

Calibre Wiring Guide

on

  • 1,006 views

CALIBRE’s exclusive, patented design mounts separate wireless radar receivers behind the front grill and rear bumper ~ strategically positioned for the fastest capture of radar signals. Distinct ...

CALIBRE’s exclusive, patented design mounts separate wireless radar receivers behind the front grill and rear bumper ~ strategically positioned for the fastest capture of radar signals. Distinct verbal or tone and visual alerts let you know exactly when and where to look for police.

With it's wireless & Datadyne technologies CALIBRE is simply the most powerful radar & laser protection system you can buy.


CALIBRE is also the only system you control with a hand-held remote, about the size of a key fob. And it's just as easy to use. With no permanently installed buttons to clutter your interior or to fuss with, you just click to select these modes: On/Off, City/Highway, Voice/Tone and Volume/Mute, then put your Wireless OneTouch™ Remote Control away until you want to change preferences.

Statistics

Views

Total Views
1,006
Views on SlideShare
1,006
Embed Views
0

Actions

Likes
0
Downloads
7
Comments
0

0 Embeds 0

No embeds

Accessibility

Categories

Upload Details

Uploaded via as Adobe PDF

Usage Rights

© All Rights Reserved

Report content

Flagged as inappropriate Flag as inappropriate
Flag as inappropriate

Select your reason for flagging this presentation as inappropriate.

Cancel
  • Full Name Full Name Comment goes here.
    Are you sure you want to
    Your message goes here
    Processing…
Post Comment
Edit your comment

    Calibre Wiring Guide Calibre Wiring Guide Document Transcript

    • BLOCK DIAGRAM CALIBRE GROUND #8 X 1/2" TEK *NOTE: THE RED WIRE SHOULD BE CONNECTED TO A MINIMUM 16 GAUGE +12 VOLT IGNITION WIRE. BLACK RED IGNITION AMPLIFIED SWITCHED SPEAKER INTERIOR +12 VOLTS NETWORK BROWN MODULE BLUE GRAY WHITE WHITE BLUE GRAY GRAY FRONT REAR FRONT REAR RADAR RADAR LED LED (CALIBRE DL model only) RECEIVER RECEIVER CABLE CABLE +12 VOLT BATTERY FUSE FUSE CONNECTION CONNECTION OR IGNITION SOURCE +12 VOLT 1AMP WHITE BLUE 1AMP BATTERY OR IGNITION SOURCE YELLOW* YELLOW* BROWN* BROWN* BLACK BLACK GROUND GROUND #8 X 1/2" TEK #8 X 1/2" TEK BROWN* BROWN* BLACK BLACK YELLOW* YELLOW* BLACK BLACK CABLE CABLE *THE YELLOW AND BROWN RADAR RECEIVER WIRES ARE USED TO CONNECT TO THE OPTIONAL LASER DEFUSER. IF NO LASER DEFUSER IS BEING INSTALLED WITH THE RADAR RECEIVER (FRONT AND/OR REAR), THE YEL- LOW AND BROWN WIRES WILL NOT BE USED. FRONT LASER DEFUSER REAR LASER DEFUSER (OPTIONAL) (OPTIONAL) IGNITION AND GROUND 1. Use a test meter to locate an ignition on source for the Interior Network Module with +12 volts when ignition key is both on and cranking. 2. Connect the black wire to a solid chassis ground using the provided ring terminal and silver self- tapping screw. 3. Radar receivers may be connected to either a +12 volt ignition on source or +12 volt constant battery source. 44586-2 07/07
    • BLOCK DIAGRAM CALIBRE GROUND #8 X 1/2" TEK *NOTE: THE RED WIRE SHOULD BE CONNECTED TO A MINIMUM 16 GAUGE +12 VOLT IGNITION WIRE. BLACK AMPLIFIED RED IGNITION SWITCHED SPEAKER INTERIOR +12 VOLTS NETWORK BROWN MODULE BLUE GRAY WHITE WHITE BLUE GRAY GRAY FRONT REAR FRONT REAR RADAR RADAR RECEIVER RECEIVER pod pod CABLE CABLE (CALIBRE DL-P +12 VOLT model only) BATTERY FUSE FUSE CONNECTION CONNECTION OR IGNITION SOURCE +12 VOLT 1AMP WHITE BLUE 1AMP BATTERY OR IGNITION SOURCE YELLOW* YELLOW* BROWN* BROWN* BLACK BLACK GROUND GROUND #8 X 1/2" TEK #8 X 1/2" TEK BROWN* BROWN* BLACK BLACK YELLOW* YELLOW* BLACK BLACK CABLE CABLE *THE YELLOW AND BROWN RADAR RECEIVER WIRES ARE USED TO CONNECT TO THE OPTIONAL LASER DEFUSER(S). IF A LASER DEFUSER IS NOT BEING INSTALLED WITH A RADAR RECEIVER (FRONT AND/OR REAR), THE YELLOW AND BROWN WIRES WILL NOT BE USED. FRONT LASER DEFUSER REAR LASER DEFUSER (OPTIONAL) (OPTIONAL) IGNITION AND GROUND 1. Use a test meter to locate an ignition on source for the Interior Network Module with +12 volts when ignition key is both on and cranking. 2. Connect the black wire to a solid chassis ground using the provided ring terminal and silver self- tapping screw. 3. Radar receivers may be connected to either a +12 volt ignition on source or +12 volt constant battery source.