Mobile t fa_for_atm_1
Upcoming SlideShare
Loading in...5
×
 

Like this? Share it with your network

Share

Mobile t fa_for_atm_1

on

  • 573 views

 

Statistics

Views

Total Views
573
Views on SlideShare
570
Embed Views
3

Actions

Likes
0
Downloads
5
Comments
0

2 Embeds 3

http://www.slideshare.net 2
http://www.lmodules.com 1

Accessibility

Categories

Upload Details

Uploaded via as Microsoft PowerPoint

Usage Rights

© All Rights Reserved

Report content

Flagged as inappropriate Flag as inappropriate
Flag as inappropriate

Select your reason for flagging this presentation as inappropriate.

Cancel
  • Full Name Full Name Comment goes here.
    Are you sure you want to
    Your message goes here
    Processing…
Post Comment
Edit your comment

Mobile t fa_for_atm_1 Presentation Transcript

  • 1. Mobile T-FA For ATM J. Nirmalraj raj S.Satheesh Kumar Ra.ja.prabu T.Suresh GUIDED BY: MISS.K.SHAYAMAL B.E
  • 2. CONTENTS
      • INTRODUCTION.
      • OBJECTIVE.
      • TWOFACTORAUTHENTICATION.
      • EXISTING METHOD.
      • PROPOSED METHOD.
      • COMPONENTS DESCRIPTION.
      • CONCLUSION.
  • 3. ATM
      • History
      • Types of security
      • Global analysis
      • services
  • 4. ATM FRAUDS
      • Card skimmers
      • Magnetic tape
      • Shoulder surfing
  • 5. SOLUTIONS
      • Anti skimmer devices,
      • Remote monitoring,
      • Security guards,
      • “ effective authentication methods”
  • 6. OBJECTIVE
      • Providing Efficient Authentication.
      • Preventing identity fraud.
  • 7. TWO FACTOR/TWO LEVEL AUTHENTICATION
      • What is T-FA?
      • Why needed?
  • 8. EXISTING METHOD
    • BIOMETRIC
    • Types
      • Contact
      • Contact less
    • Drawbacks
      • Cost
      • Maintenance
  • 9. PROPOSED METHOD MOBILE based authentication ATM MACHINE AUTHENTICATION AGENT USER MOBILE SUCCESS FULL AUTHNETICATION
  • 10. APPLICATIONS WEB AUTHENTICATION SERVER USER MAN IN THE MIDDLE
  • 11. BLOCK DIAGRAM PIC 16F887A CARD HOLDER GSM INTERNAL SECURITY MOBILE AUTHENTICATION AGENT MEMORY
  • 12. COMPONENT DESCRIPTION
      • MT8870
      • PIC 16F887A
      • USART
      • INTER INTEGRATED CIRCUIT
  • 13. INTRODUCTION
      • DTMF stands for dual tone multiple frequency
      • It is also known as touch-tone ,tone dialing.
      • Each DTMF tone consists of two simultaneous tones
      • Tones travel through the red and green wires, in a telephone.
  • 14. KEYPAD
  • 15. Tone 1:Frequency + = Low frequency High frequency
  • 16. MT8870 DECODER IC
  • 17. TIMING DIAGRAM
  • 18. ABOUT PIC
      • PIC is stands for Peripheral Inter Face controller.
      • PIC microcontroller is used for the controlling.
      • 40 pin IC.
      • 33 I/O pins.
      • Operating voltage 5V.
      • Operating frequency 4-20 mhz.
  • 19. REASON FOR USING PIC
      • Harvard Architecture
      • Instruction Pipelining
      • RISC
      • Only 35 single word instruction
  • 20. I2C
      • I2C is Inter Integrated Circuit.
      • Communication between the EEPROM card
    • and controller is I2C.
      • I2C can easily link multiple devices.
      • It provides good support for communication.
  • 21.
    • I2C is a serial interface of only two signals.
      • SDA
      • SCL
  • 22. I2C DATA TRANSFER. SSPBUF MASTER CONTROL ACTION SLAVE
  • 23. USART
      • Universal Synchronous/Asynchronous Receiver/Transmitter.
      • Serial data communication between PIC and terminal.
      • We used asynchronous mode.
      • half duplex
          • typically asynchronously
          • 5 – 9 bits of data
          • 2 or 3 framing bits
            • start bit
            • 1 or 2 stop bits
          • 0 or 1 parity bits
  • 24. ASYNCHRONOUS MODE
      • Baud rate generator.
      • Asynchronous transmitter.
  • 25. Baud Rate Generator (BRG)
      • It support both asynchronous and synchronous mode.
      • SPBRG
      • Baud rate formula
  • 26. ASYNCHRONOUS TRANSMITTER
  • 27. ASYNCHRONOUS MASTER TRANSMISSION
  • 28.  
  • 29. COMPARISON
      • SECURITY
      • USABILITY
      • ECONOMY
  • 30. CONCLUSION