Certificate number: FS453/04
FS20 FIRESTOP MORTAR
Application
FS20 Firestop Compound is used to provide a fire
rated seal ...
Load Bearing Fire Seals
The open area free of services: thickness of seal
ratios for non-reinforced seals given above, all...
Upcoming SlideShare
Loading in …5
×

Fs20 fire coating in canada, intumescent fire protection coating, fireproofing spray

142 views
95 views

Published on

Steel Fire Protection experts providing installation and application of structural steel fire protection for Indoor and Outdoor. We provide reliable and cost effective Steel Fire Protection, Intumescent Coatings, Fire Coating, Cable Coating, Fire Stopping, Fireproofing Spray, Fireproofing and Fire Protection Products worldwide like Middle East, USA, Canada, Africa, , Bahrain, Saudi Arabia, Turkmenistan, Malaysia, Indonesia, UAE

Published in: Business
0 Comments
0 Likes
Statistics
Notes
  • Be the first to comment

  • Be the first to like this

No Downloads
Views
Total views
142
On SlideShare
0
From Embeds
0
Number of Embeds
1
Actions
Shares
0
Downloads
2
Comments
0
Likes
0
Embeds 0
No embeds

No notes for slide

Fs20 fire coating in canada, intumescent fire protection coating, fireproofing spray

  1. 1. Certificate number: FS453/04 FS20 FIRESTOP MORTAR Application FS20 Firestop Compound is used to provide a fire rated seal around service penetrations in fire rated walls and floors. Tested in accordance with BS 476:Part 22, Fire Security Firestop Compound provides up to 6 hours fire protection. General benefits: • Smoke seal • Good acoustic insulation • Simple installation • Load bearing seal • Suitable to make good around most types of service penetrations • Unaffected by humidity • Maintenance free • No smoke emission Fire Rating Acoustic Description FS20 Firestop Compound is a specially formulated gypsum based mortar, which is mixed with water to be trowelled or poured around service penetrations. Plastic pipework must be protected with either Fire Security Firestop Collars or Intumescent Pipe Wraps (see data sheets). In floors, permanent formwork panel (50mm) is cut and friction fitted between services and the edges of the floor slab. FS20 Firestop Compound is then trowelled over the formwork to a depth of 25mm thick. This is allowed to harden. The FS20 Firestop Compound is then mixed to a pouring grade and tops the seal up to the required depth. In walls, FS20 Firestop Compound is mixed into a stiff consistency for trowelling into smaller openings. In larger openings, FS20 Firestop Compound can be cast into blocks which can be built into walls. Coverage These are approximate calculations based on 22kg bags. The coverage does not take into account the percentage of the hole filled with services. Specification Install FS20 Firestop Compound to provide 1,2,3 or 4 hour fire rating to all service penetrations through all fire rated walls and floors. Installation to be fully in accordance with manufacturer’s instructions. Tested to BS 476:Part 22 0 3hr 6hr Fire Rating You can request from our technical sales office the following information: • Material Safety Data Sheets • Installation Instructions • Product Certification FS20 Firestop Compound SERVICEPENETRATIONS TECHNICAL INFORMATION Fire Rating Thickness of Mortar 1-2 Hours 75mm 3-6 Hours 100mm Thickness of Mortar Number of Bags per m² 75mm 3.15 100mm 4.2 150mm 6.3 FIRE RATINGS Thickness of Mortar Weighted Sound Reduction Index (Rw) 50mm 39dB 100mm 46dB 150mm 51dB
  2. 2. Load Bearing Fire Seals The open area free of services: thickness of seal ratios for non-reinforced seals given above, allow an ample safety margin for normal foot traffic e.g. loads of two men plus equipment with a combined weight of up to 200kg. FS20 Firestop Compound sets in 30-45 minutes and is capable of accommodating foot traffic in approximately 72 hours. * As a further safety margin, we would recommend that all floor seals with clear areas greater than in the above table must be reinforced. Please contact our technical department for details. When ordering this product you will need the following information: • Size of opening • Details of service penetrations • Fire rating • Quantity required Please order from our technical sales office. Canada: PO Box 21096, Coquitlam BC V3E 3P9 Canada P: +1 604 941 1001 F: +1 604 648 9311 Norway: Skibåsen 20b -4636 Kristiansand Norway P: +47 95 47 80 00 F: +47 38 02 15 31 UAE: PO Box 40068 Ajman UAE P: +971 6 7478842 F: +971 6 7478843 Email: mail@fire-security.net www.fire-security.net ORDERING FS20 Firestop Compound trowelled into wall. FS20 Firestop Compound SERVICEPENETRATIONS Thickness of Mortar Load Bearing Area Free of Services 75mm 500 x 500mm * 100mm 750 x 750mm * FS20 Firestop Compound poured onto permanent mineral fibre shutter in floor.

×