Exj 8 la
Upcoming SlideShare
Loading in...5
×
 

Exj 8 la

on

  • 268 views

 

Statistics

Views

Total Views
268
Views on SlideShare
268
Embed Views
0

Actions

Likes
0
Downloads
0
Comments
0

0 Embeds 0

No embeds

Accessibility

Upload Details

Uploaded via

Usage Rights

© All Rights Reserved

Report content

Flagged as inappropriate Flag as inappropriate
Flag as inappropriate

Select your reason for flagging this presentation as inappropriate.

Cancel
  • Full Name Full Name Comment goes here.
    Are you sure you want to
    Your message goes here
    Processing…
Post Comment
Edit your comment

Exj 8 la Exj 8 la Document Transcript

  • XJ LAMPS 8L - 1 LAMPS CONTENTS page pageREMOVAL AND INSTALLATION FRONT TURN SIGNAL . ................... 2 BACKUP, REAR TURN SIGNAL, TAILLIGHT AND HEADLIGHTS . . . . . . . ................... 1 REAR FOG LIGHT . . . . . . . . . . . . . . . . . . . . . 2 SIDE REPEATER LIGHT .................. 1 CENTER HIGH MOUNTED STOPLIGHT . . . . . . . 2 SPECIFICATIONS FRONT FOG LAMP . . . . . . . . . . . . . . . . . . . . . . 2 REPLACEMENT BULBS ................... 3 FRONT POSITION LIGHT . . . . . . . . . . . . . . . . . 1REMOVAL AND INSTALLATION SIDE REPEATER LIGHTHEADLIGHTS REMOVAL 1. Insert a small, flat bladed pry tool in slot pro-REMOVAL vided at the bottom side of the side repeater lamp 1. Remove the 2 screws holding the bezel in place bulb to socket.and remove bezel (Fig. 1). 2. Pry lamp lens from lamp housing. 2. Remove the 4 screws holding the headlight and 3. Rotate and pull the bulb from the socket (Fig.replace the bulb from the rear of the housing (Fig. 2). 3). Fig. 1 Headlight Bezel Fig. 3 Side Repeater LightINSTALLATION INSTALLATION 1. Align the side repeater lamp bulb to the socket (Fig. 3). 2. Push and twist the bulb into the socket. 3. Position the top edge of the lamp lens to the lip on the lamp housing. 4. Press downward until the lamp lens is fully seated to the lip. 5. Verify lamp operation. FRONT POSITION LIGHT REMOVAL 1. Remove the 2 screws holding the headlight bezel in place and remove the bezel (Fig. 1). Fig. 2 Headlight Housing 2. Remove the 4 screws holding the headlight 1. Reverse the removal procedures to install. housing (Fig. 2).
  • 8L - 2 LAMPS XJREMOVAL AND INSTALLATION (Continued) 3. Pull the front position light socket from the rub- 3. Remove the lamp element from the housingber grommet and replace the bulb (Fig. 4). (Fig. 6). Fig. 4 Front Position Light Fig. 6 Front Fog LightINSTALLATION INSTALLATION 1. Reverse the removal procedure for installation. 1. Install the new lamp element in the housing and reinstall the lower housing.FRONT TURN SIGNAL BACKUP, REAR TURN SIGNAL, TAILLIGHT ANDREMOVAL REAR FOG LIGHT 1. Remove the 2 screws holding the bezel in placeand remove the bezel (Fig. 1). REMOVAL 2. Remove the screws holding the turn signal 1. There are 3 mounting bolts attaching the tail-housing in place (Fig. 5). light assembly. When removing, unfasten the 3 bolts 3. Remove the turn signal housing. located on the top and side. Do not remove the bot- 4. Twist the socket from the back of the turn sig- tom shoulder bolt; lift up and out to remove thenal housing and then pull from the socket. assembly. 2. Turn the bulb assembly 1/3 turn and pull the bulb from the socket to replace the bulb (Fig. 7). Fig. 5 Front Turn Signal BulbINSTALLATION 1. Reverse the removal procedure to install. Fig. 7 Rear Lamp Replacement INSTALLATIONFRONT FOG LAMP 1. Reverse the removal procedure to install.REMOVAL CENTER HIGH MOUNTED STOPLIGHT 1. Remove the 2 screws from the bottom cover ofthe lamp body (Fig. 5). REMOVAL 2. Disconnect the 2 wires from the lamp element. 1. Remove the 2 screws (Fig. 8). 2. Rotate the bulb sockets 1/4 turn and pull from the housing.
  • XJ LAMPS 8L - 3REMOVAL AND INSTALLATION (Continued) SPECIFICATIONS REPLACEMENT BULBS Interior Lamps Bulb Type Auto. Trans. Floor Shift Lamp . . . . . . . . . . . . . . 658 Cargo Lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . 561 Climate Control Lamp (2) . . . . . . . . . . . . . . . . . . 74 Dome Lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . 561 Dome/Reading Lamp . . . . . . . . . (1) 561 and (2) 906 Glove Box Lamp . . . . . . . . . . . . . . . . . . . . . . . . . 194 Lighted Vanity Mirror (2)* . . . . . . . . . . . . . . . . . . 74 Map Reading Light in Overhead Console (4) . . . 912 Fig. 8 Center High Mounted Stoplight Rocker Switch Lamp . . . . . . . . . . . . . . . . . . . . . . 37 Transfer Case Lamp . . . . . . . . . . . . . . . . . . . . . . 658INSTALLATION Underpanel Courtesy Lamps (2) . . . . . . . . . . . . . 168 1. Reverse the removal procedure for installation. * Available only at Chrysler Dealers.