v.03 New Diagram for the Implementation of the EN 81-1/2:1998+A3:2009 (UCM) Standards in our Products.
Upcoming SlideShare
Loading in...5
×
 

v.03 New Diagram for the Implementation of the EN 81-1/2:1998+A3:2009 (UCM) Standards in our Products.

on

  • 750 views

In view of the numerous doubts and queries from you, concerning the compliance with Standards: EN 81-1:1998+A3:2009 and EN 81-2:1998+A3:2009, we have produced a diagram in order to explain the ...

In view of the numerous doubts and queries from you, concerning the compliance with Standards: EN 81-1:1998+A3:2009 and EN 81-2:1998+A3:2009, we have produced a diagram in order to explain the processes relating to our products.

This is an explanatory diagram that is constantly updated. As soon as there are any modifications in it, you will be informed by this same channel. We hope this information may be of use and help to you.

http://dynatech-elevation.com/pub/documentos/documentos_cuadro_UCM_v01_ingles_2abea81a.pdf

Statistics

Views

Total Views
750
Views on SlideShare
748
Embed Views
2

Actions

Likes
0
Downloads
1
Comments
0

1 Embed 2

http://www.pinterest.com 2

Accessibility

Categories

Upload Details

Uploaded via as Adobe PDF

Usage Rights

© All Rights Reserved

Report content

Flagged as inappropriate Flag as inappropriate
Flag as inappropriate

Select your reason for flagging this presentation as inappropriate.

Cancel
  • Full Name Full Name Comment goes here.
    Are you sure you want to
    Your message goes here
    Processing…
Post Comment
Edit your comment

v.03 New Diagram for the Implementation of the EN 81-1/2:1998+A3:2009 (UCM) Standards in our Products. v.03 New Diagram for the Implementation of the EN 81-1/2:1998+A3:2009 (UCM) Standards in our Products. Presentation Transcript

  • UCM_v.03   UCMA3 Requirements:Item 9.11 of EN81‐1:1998+A3:2009‐ car stop must be caused without exceeding 1.20 m‐ ascending deceleration of 1 g must not be allowed and the values accepted for the safety gears must be allowed in descending deceleration Safety ElementsPer UnitThe customer has a unit certified as UCM and does not need to check the requirements requested in the A3 at his/her installationD‐Box + VEGA+ ASG+ T‐25 CM/040/12D‐Box + STAR + ASG+ T‐25 CM/045/12D‐Box +QUASAR T25+ ASG CM/060/13Per ComponentThe customer makes the UCM solutions according to his/her needs; however he/she must be held responsible for checking that the unit meets the A3 requirements in his/her installation GovernorsStar A3 ATI/LD‐VA/M‐126A‐1/11Vega A3 ATI/LD‐VA/M‐155A‐3/11LBD‐300 A3 MD/EVN/130031QUASAR SV A3 ATI/LD/VA/M207/13QUASAR T25 A3 ATI/LD/VA/M207/13Safety gear+Dynatech Steering MechanismsPR‐2500 ATI/LD‐VA/M‐062A‐1/11PR‐2500 UD ATI/LD‐VA/M‐065A‐3/11PR‐2000 UD ATI/LD‐VA/M‐105A‐1/11PQ‐3400 UD ATI/LD‐VA/M‐126A‐1/11PQ‐4000 UD ATI/LD‐VA/M‐120A‐1/11ASG series ATI/LD‐VA/M‐154A‐2/11ASG‐UD series ATI/LD‐VA/M‐154A‐2/11Control SystemD‐Box CM‐029‐11ControllerTo be certified by the operatorDrive MachinePer UnitTornado + Dynatech control System (CDC‐060 and BFS‐059)CM/027/11Per ComponentMachine Tornado ‐ CM/028‐1/11Control SystemsCDC‐060 CM/043/12BFS‐059 CM/044/12Controller To be certified by the operator+++