DIY Recessed Power Outlet and Cable Management products. Check out their complete line up here: http://www.wiredathome.com/brands/PowerBridge.html

1. In-Wall Power Cable Management for HDTV
www.PowerBridge1.com
jpistol@powerbridgesolution.com
303.683.2434 x300

2. WHITE PAPER: Installation Compliance
GENERAL:
Conform to US Standards UL498, UL 514C, UL817 and Canadian CSA Standard C22.2 NOs 21, 42.1
INTENDED USE:
PowerBridge Solution is certified for installation to provide a single location in-wall/ceiling power extension
using code compliant building power cable within enclosed walls or ceiling areas. Installation conforms to NEC
Chapter 3 Wiring Methods. Performs extension of 120-volt A.C. power from an existing power source, such as,
not limited to; an existing installed outlet receptacle or external UL Listed power bar or extension surge
protection device through external use of a UL Listed power supply cable.
------BUILDING POWER CABLE: Nonmetallic-sheathed cable, also known as *ROMEX®, UL Listed NM-type
cable is the most common and most accepted building premise power cable used for 120-volt wiring of lights,
outlets and switches. Supplied 14-2 gauge NM-type building cable can be utilized in all areas of the US and
Canada where NM-type cable is approved to meet code compliancy. EXCEPTION: Cook County, IL – NYC, NY
INSTALLATION PREMISE:
Installation of the PowerBridge creates a dead-front extension, meaning it is not wired to the live premise
branch- circuit power. PowerBridge remains as a dead-front, defined as without live parts until it is energized by
means from the dead-front inlet through a suitable UL Listed power supply cord from the front of the existing
power circuit, through its rated receptacle outlet. Benefit to this method of installation allows connection to an
external power conditioner/surge protection device, bridging protected power in-wall to wall mounted display
and audio appliances.
------· PowerBridge is not installed as part of the building premise power circuit.
· PowerBridge is not wired to, or made permanently part of, the building electrical circuit or branch-circuit.
· Installation does not create a new circuit, also known as a branch-circuit or branch-circuit extension.
· Installation does not change, modify, alter, or add-to, the premise power circuit as it is not direct wired to
the premise power circuit.
POWERCONNECTOR NM-TYPE POWER CABLE CONNECTORS:
BENEFITS:
PowerBridge innovated use of pre-terminated NM Connectors for plug-together connection of supplied preterminated NM-type building power cable. No tools required. Installer friendly, no special training or skill
required to connect. Safely and correctly allows fast plug-to-plug connection between the pre-terminated
PowerIN and PowerOUT wall plates without hard wiring to termination screw attachment points. Ensures
integrity of NM Cable connection, using secure locked termination points.

3. INSTALLATION CODE APPROVALS:
Conforms for use within National Electrical Code (NEC)
Approval for PowerConnectors:
*NEC Article 334.40 (B) Devices of Insulating Material.
“- tap devices of insulating material shall be permitted to be used without boxes in exposed cable wiring for
rewiring in existing buildings where the cable is concealed and fished. Openings in such devices shall form a
close fit around the outer covering of the cable and the device shall fully enclose the part of the cable from which
any part of the covering has been removed.”
Approval for installation of NM cable within walls:
*NEC Article 334.30 (B) Unsupported Cables.
“Nonmetallic-sheathed cable shall be permitted to be unsupported where the cable is fished between access
points through concealed spaces in finished buildings or structures and supporting is impracticable.”
Approval for installation of assembled Listed kit:
*NEC Article 400.7 (A) (11) Flexible Cords and Cables - Uses Permitted
“Between an existing receptacle outlet and an inlet, where the inlet provides power to an additional receptacle
outlet. The wiring interconnecting the inlet to the receptacle outlet shall be a Chapter 3 wiring method. The inlet,
receptacle outlet, and Chapter 3 wiring method, including the flexible cord and fittings, shall be a listed
assembly specific for this application.”
Applicable products manufactured by HD Products for:
PowerBridge: ONE-CK, TWO-CK, SBCK, SWCK, CKRE, ONE-PRO, TWO-PRO, SWPR, SBPR
HD Products, LLC. PowerBridge Solution. 3869 Norwood Dr. #5 Littleton, CO 80125 | 303.683.2434 x300
info@powerbridgesolution.com
|
www.PowerBridgeSolution.com
© 2013 HD Products, Inc., PowerBridge Solution
*ROMEX® is Trademark of the Southwire Company.
*© NEC® National Electrical Code® Trademarks of the NFPA

4. In-Wall Recessed Power Cable Management - PowerConnect
MODEL
ONE-CK
Conceal cables and power for your wall mounted TV
Introducing the all new ONE-CK in-wall power and cable
management system. Single-gang size all-in-one design.
Designed to simplify wiring behind wall-mounted flat-panel TV’s
This discreet system allows low voltage cables and wires to be
Power Extension
In-Wall
routed through the wall for a clean look.
AV Cables
In-Wall
Code Compliant to install power, includes hardware and helpful
mounting template make the ONE-CK the perfect do-it-yourself
solution for any skill level, without the need for an electrician.
No wiring, simple snap together PowerConnectors make this
safe and easy.
CK - ConnectorKit Series
ONE-CK, TWO-CK
So simple...
You can do this!
Pre-Wired In-Wall PowerConnectors
No assembly of parts. No wiring to electrical system
Code Compliant throughout the US and Canada
Safe - Click-it together like a safety belt
MODEL
ONE-CK
Recessed extra deep 1.5”
Extra wide opening for
all types of TV cords.
Works with super-slim
mounts, creating more
usable space behind
your wall-mounted TV
PRODUCT DIMENSIONS
(w x d x h)
2.75” x 3.00” x 4.5”
6.9 x 9.5 x 11.4 cm
PACKAGE DIMENSIONS
(w x d x h)
7.75” x 4” x 7”
18.3 x 10.6 x 17.8 cm
PACKAGE WEIGHT
2.4 lbs / 10.7 kg
MASTER PACK QUANTITY
10
FINISH
White
In-wall power connectors
ensure simple snap
connection without the
need for an electrician.
Pre-wired 80” in-wall wire
UPC
855877002868
CODE COMPLIANCY
SUPPORT
1) NEC 2005 Article 334.40(B)
One piece pre-assembled
power-wiring with connectors
Depth: 3.75” fits in any
2x4 - 2x6 framed wall
PowerConnector tap-device
2) NEC Article 334.30
Unsupported NM Cable
3) NEC 2014 Article 400.7(A)(11)
Permitted use of cord / approved kit
using inlet to energize receptacle
Meets all US states and cities
adaptive to the National
Electrical Code (NEC)
allowing NM type building cable.
Specific locations not allowing NM
type building cable:
~Cook County, IL
~NYC, NY
Conforms to UL Standards
498 & 514C
AVAILABILITY
Current
Recessed, in-wall installation
conceals component cables
for a flawless finished look
with brush pass-through
4.5”
2.75”
plug into surge protector
Code Compliant
6’ power-cord energizes
PowerINLET from existing
receptacle or external
surge protector.
Single-gang - Same size as
a standard wall plate.

5. In-Wall Recessed Power Cable Management Dual Power - PowerConnect
MODEL
TWO-CK
Conceal cables and power for your wall mounted TV
Introducing the all new TWO-CK in-wall dual outlet power
and cable management system. Perfect for motorized mounts.
Same size as standard dual and single wall plates.
Designed to simplify wiring behind wall-mounted flat-panel TV’s
This discreet system allows low voltage cables and wires to be
Power Extension
In-Wall
AV Cables
In-Wall
routed through the wall for a clean look.
Code Compliant to install power, includes hardware and helpful
mounting template make the TWO-CK the perfect do-it-yourself
solution for any skill level, without the need for an electrician.
No wiring, simple snap together PowerConnectors
make this safe and easy.
CK - ConnectorKit Series
ONE-CK, TWO-CK
So simple...
You can do this!
Pre-Wired In-Wall PowerConnectors
No assembly of parts. No wiring to electrical system
Code Compliant throughout the US and Canada
Safe - Click-it together like a safety belt
MODEL
TWO-CK
Dual PowerConnect Kit
PRODUCT DIMENSIONS
(w x d x h)
PowerINLET
2.75” x 3.00” x 4.5”
Recessed extra deep 1.5”
Extra wide opening for
all types of TV cords.
Works with super-slim mounts,
creating more usable space
behind your wall-mounted TV
PowerOUTLET
4.5” x 3.25” x 4.5”
PACKAGE DIMENSIONS
(w x d x h)
8.5” x 4” x 8”
21 x 10 x 19.3 cm
PACKAGE WEIGHT
2.9 lbs / 12.1 kg
MASTER PACK QUANTITY
10
In-wall power connectors
ensure simple snap
connection without the
need for an electrician.
Pre-wired 80” in-wall wire
PowerOUTLET - Dual-gang
Same size as a standard
wall-plate.
FINISH
White
UPC
855877002950
CODE COMPLIANCY
SUPPORT
1) NEC 2005 Article 334.40(B)
One piece pre-assembled
power-wiring with connectors
Depth: 3.75” fits in any
2x4 - 2x6 framed wall
PowerConnector tap-device
2) NEC Article 334.30
Unsupported NM Cable
3) NEC 2014 Article 400.7(A)(11)
Permitted use of cord / approved kit
using inlet to energize receptacle
Meets all US states and cities
adaptive to the National
Electrical Code (NEC)
allowing NM type building cable.
Specific locations not allowing NM
type building cable:
~Cook County, IL
~NYC, NY
AVAILABILITY
Current
Recessed, in-wall installation
conceals component cables
for a flawless finished look
with brush pass-through
Code Compliant
6’ power-cord energizes
PowerINLET from existing
receptacle or external
surge protector.
plug into surge protector
4.5”
2.75”
PowerINLET - Single-gang
Same size as a standard wall plate.

6. SoundBar Power Solution with PowerConnect
MODEL
SBCK
Recessed, slim design power for your wall mounted SoundBar
Introducing the all new SBCK in-wall recessed power
and cable management system for popular wall-mounted
SoundBars.
Only 2.5” tall, designed to conceal behind slim SoundBars
This discreet system allows digital audio cables to be
Power Extension
In-Wall
routed through the wall for a clean look.
AV Cables
In-Wall
Compliments a complete in-wall installation when installed with
ONE-CK, TWO-CK, Power kits.
No wiring, simple snap together PowerConnectors make this
safe and easy.
So simple...
You can do this!
CK - ConnectorKit Series
ONE-CK, TWO-CK
Pre-Wired In-Wall PowerConnectors
No assembly of parts. No wiring to electrical system
Code Compliant throughout the US and Canada
Safe - Click-it together like a safety belt
MODEL
SBCK
SoundBar Connector Kit
PRODUCT DIMENSIONS
(w x d x h)
11.75” x 2.0” x 2.5”
29.8 x 5 x 64 cm
PACKAGE DIMENSIONS
(w x d x h)
12” x 5” x 3”
30.5 x 12.7 x 7.6 cm
PACKAGE WEIGHT
2.0 lbs / 8.9 kg
MASTER PACK QUANTITY
10
FINISH
White
UPC
855877002974
CODE COMPLIANCY
SUPPORT
1) NEC 2005 Article 334.40(B)
SoundBar with ONE-CK
Single Power Kit
SoundBar with TWO-CK
Dual Power Kit
1’ Prewired
PowerConnector
to TV Outlet
Connector
PowerConnector tap-device
2) NEC Article 334.30
Unsupported NM Cable
3) NEC 2014 Article 400.7(A)(11)
In-wall Digital Audio Cable
from TV to SoundBar
Permitted use of cord / approved kit
using inlet to energize receptacle
Meets all US states and cities
adaptive to the National
Electrical Code (NEC)
allowing NM type building cable.
Specific locations not allowing NM
type building cable:
~Cook County, IL
~NYC, NY
AVAILABILITY
January 2014
6’ Prewired
PowerConnector
to Power-Inlet
Connector
Recessed, in-wall installation
conceals audio cables
for a flawless finished look
with rubber pass-through
Completely recessed area for power cord
Conceals behind SoundBars, allows
for ultra-close wall mounting
One piece pre-assembled
power-wiring with connectors
Depth: 2” fits in any
2x2 - 2x4 - 2x6 framed wall

7. In-wall PowerConnector Extension
MODEL
CKRE
Extend PowerConnect Cable to remote location
Introducing the all new CKRE in-wall power cable extension.
Pre-assembled 10, 20, 30 foot lengths can be used to extend
up to an additional 50’ distance for remote power locations.
Ideal for custom installation above fireplace, remote
equipment closet/room.
Compliments a complete in-wall installation when installed with
ONE-CK, TWO-CK, and SBCK Power kits.
No wiring, simple snap together PowerConnectors make this
safe and easy.
Ideal for new home pre-wire
CK - ConnectorKit Series
ONE-CK, TWO-CK
Pre-Wired In-Wall PowerConnectors
MODEL
No assembly of parts. No wiring to electrical system
Code Compliant throughout the US and Canada
CKRE
Safe - Click-it together like a safety belt
PRODUCT DIMENSIONS
(Length)
10’- 20’ - 30’
3.4 - 6.09 - 9.14 m
Pre-Assembled 6’ Length
from PowerOUT
PACKAGE DIMENSIONS
(w x d x h)
7” x 2” x 7”
17.78 x 5 x 17.78 cm
Pre-Assembled Power Connector Extension
Available 10’ - 20’ - 30’
Extend up to 50’
PACKAGE WEIGHT
1.0 lbs / 4.5 kg
MASTER PACK QUANTITY
5
Pre-Assembled 1’ Length
from PowerIN
MODELS
CKRE-10
CKRE-20
CKRE-30
CODE COMPLIANCY
SUPPORT
1) NEC 2005 Article 334.40(B)
PowerConnector tap-device
2) NEC Article 334.30
Unsupported NM Cable
Meets all US states and cities
adaptive to the National
Electrical Code (NEC)
allowing NM type building cable.
Specific locations not allowing NM
type building cable:
~Cook County, IL
~NYC, NY
AVAILABILITY
Current
So simple...
You can do this!
Extend ONE-CK
Single Power Kit
Extend TWO-CK
Dual Power Kit