Upcoming SlideShare
×

# Schaum's outline electric circuits 4th ed (2003)

21,328
-1

Published on

Electric Circuits PDF, which help in understanding the basics of electric circuits with exercises and examples.

Published in: Education
37 Likes
Statistics
Notes
• Full Name
Comment goes here.

Are you sure you want to Yes No
• Be the first to comment

Views
Total Views
21,328
On Slideshare
0
From Embeds
0
Number of Embeds
3
Actions
Shares
0
3,785
0
Likes
37
Embeds 0
No embeds

No notes for slide

### Schaum's outline electric circuits 4th ed (2003)

1. 1. Theory and Problems of ELECTRIC CIRCUITS Fourth Edition MAHMOOD NAHVI, Ph.D. Professor of Electrical Engineering California Polytechnic State University JOSEPH A. EDMINISTER Professor Emeritus of Electrical Engineering The University of Akron Schaum’s Outline Series McGRAW-HILL New York Chicago San Francisco Lisbon London Madrid Mexico City Milan New Dehli San Juan Seoul Singapore Sydney Toronto
3. 3. This book is designed for use as a textbook for a ﬁrst course in circuit analysis or as a supplement tostandard texts and can be used by electrical engineering students as well as other engineereing andtechnology students. Emphasis is placed on the basic laws, theorems, and problem-solving techniqueswhich are common to most courses. The subject matter is divided into 17 chapters covering duly-recognized areas of theory and study.The chapters begin with statements of pertinent deﬁnitions, principles, and theorems together withillustrative examples. This is followed by sets of solved and supplementary problems. The problemscover a range of levels of diﬃculty. Some problems focus on ﬁne points, which helps the student to betterapply the basic principles correctly and conﬁdently. The supplementary problems are generally morenumerous and give the reader an opportunity to practice problem-solving skills. Answers are providedwith each supplementary problem. The book begins with fundamental deﬁnitions, circuit elements including dependent sources, circuitlaws and theorems, and analysis techniques such as node voltage and mesh current methods. Thesetheorems and methods are initially applied to DC-resistive circuits and then extended to RLC circuits bythe use of impedance and complex frequency. Chapter 5 on ampliﬁers and op amp circuits is new. The opamp examples and problems are selected carefully to illustrate simple but practical cases which are ofinterest and importance in the student’s future courses. The subject of waveforms and signals is alsotreated in a new chapter to increase the student’s awareness of commonly used signal models. Circuit behavior such as the steady state and transient response to steps, pulses, impulses, andexponential inputs is discussed for ﬁrst-order circuits in Chapter 7 and then extended to circuits ofhigher order in Chapter 8, where the concept of complex frequency is introduced. Phasor analysis,sinuosidal steady state, power, power factor, and polyphase circuits are thoroughly covered. Networkfunctions, frequency response, ﬁlters, series and parallel resonance, two-port networks, mutual induc-tance, and transformers are covered in detail. Application of Spice and PSpice in circuit analysis isintroduced in Chapter 15. Circuit equations are solved using classical diﬀerential equations and theLaplace transform, which permits a convenient comparison. Fourier series and Fourier transforms andtheir use in circuit analysis are covered in Chapter 17. Finally, two appendixes provide a useful summaryof the complex number system, and matrices and determinants. This book is dedicated to our students from whom we have learned to teach well. To a large degree itis they who have made possible our satisfying and rewarding teaching careers. And ﬁnally, we wish tothank our wives, Zahra Nahvi and Nina Edminister for their continuing support, and for whom all theseeﬀorts were happily made. MAHMOOD NAHVI JOSEPH A. EDMINISTER
6. 6. vi Contents 4.10 Maximum Power Transfer Theorem 47CHAPTER 5 Ampliﬁers and Operational Ampliﬁer Circuits 64 5.1 Ampliﬁer Model 64 5.2 Feedback in Ampliﬁer Circuits 65 5.3 Operational Ampliﬁers 66 5.4 Analysis of Circuits Containing Ideal Op Amps 70 5.5 Inverting Circuit 71 5.6 Summing Circuit 71 5.7 Noninverting Circuit 72 5.8 Voltage Follower 74 5.9 Differental and Difference Ampliﬁers 75 5.10 Circuits Containing Several Op Amps 76 5.11 Integrator and Differentiator Circuits 77 5.12 Analog Computers 80 5.13 Low-Pass Filter 81 5.14 Comparator 82CHAPTER 6 Waveforms and Signals 101 6.1 Introduction 101 6.2 Periodic Functions 101 6.3 Sinusoidal Functions 103 6.4 Time Shift and Phase Shift 103 6.5 Combinations of Periodic Functions 106 6.6 The Average and Effective (RMS) Values 107 6.7 Nonperiodic Functions 108 6.8 The Unit Step Function 109 6.9 The Unit Impulse Function 110 6.10 The Exponential Function 112 6.11 Damped Sinusoids 114 6.12 Random Signals 115CHAPTER 7 First-Order Circuits 127 7.1 Introduction 127 7.2 Capacitor Discharge in a Resistor 127 7.3 Establishing a DC Voltage Across a Capacitor 129 7.4 The Source-Free RL Circuit 130 7.5 Establishing a DC Current in an Inductor 132 7.6 The Exponential Function Revisited 132 7.7 Complex First-Order RL and RC Circuits 134 7.8 DC Steady State in Inductors and Capacitors 136 7.9 Transitions at Switching Time 136 7.10 Response of First-Order Circuits to a Pulse 139 7.11 Impulse Response of RC and RL Circuits 140 7.12 Summary of Step and Impulse Responses in RC and RL Circuits 141 7.13 Response of RC and RL Circuits to Sudden Exponential Excitations 141 7.14 Response of RC and RL Circuits to Sudden Sinusoidal Excitations 143 7.15 Summary of Forced Response in First-Order Circuits 143 7.16 First-Order Active Circuits 143CHAPTER 8 Higher-Order Circuits and Complex Frequency 161 8.1 Introduction 161
7. 7. Contents vii 8.2 Series RLC Circuit 161 8.3 Parallel RLC Circuit 164 8.4 Two-Mesh Circuit 167 8.5 Complex Frequency 168 8.6 Generalized Impedance ðR; L; CÞ in s-Domain 169 8.7 Network Function and Pole-Zero Plots 170 8.8 The Forced Response 172 8.9 The Natural Response 173 8.10 Magnitude and Frequency Scaling 174 8.11 Higher-Order Active Circuits 175CHAPTER 9 Sinusoidal Steady-State Circuit Analysis 191 9.1 Introduction 191 9.2 Element Responses 191 9.3 Phasors 194 9.4 Impedance and Admittance 196 9.5 Voltage and Current Division in the Frequency Domain 198 9.6 The Mesh Current Method 198 9.7 The Node Voltage Method 201 9.8 ´ Thevenin’s and Norton’s Theorems 201 9.9 Superposition of AC Sources 202CHAPTER 10 AC Power 219 10.1 Power in the Time Domain 219 10.2 Power in Sinusoudal Steady State 220 10.3 Average or Real Power 221 10.4 Reactive Power 223 10.5 Summary of AC Power in R, L, and C 223 10.6 Exchange of Energy Between an Inductor and a Capacitor 224 10.7 Complex Power, Apparent Power, and Power Triangle 226 10.8 Parallel-Connected Networks 230 10.9 Power Factor Improvement 231 10.10 Maximum Power Transfer 233 10.11 Superposition of Average Powers 234CHAPTER 11 Polyphase Circuits 248 11.1 Introduction 248 11.2 Two-Phase Systems 248 11.3 Three-Phase Systems 249 11.4 Wye and Delta Systems 251 11.5 Phasor Voltages 251 11.6 Balanced Delta-Connected Load 252 11.7 Balanced Four-Wire, Wye-Connected Load 253 11.8 Equivalent Y and Á-Connections 254 11.9 Single-Line Equivalent Circuit for Balanced Three-Phase Loads 255 11.10 Unbalanced Delta-Connected Load 255 11.11 Unbalanced Wye-Connected Load 256 11.12 Three-Phase Power 258 11.13 Power Measurement and the Two-Wattmeter Method 259CHAPTER 12 Frequency Response, Filters, and Resonance 273 12.1 Frequency Response 273
8. 8. viii Contents 12.2 High-Pass and Low-Pass Networks 274 12.3 Half-Power Frequencies 278 12.4 Generalized Two-Port, Two-Element Networks 278 12.5 The Frequency Response and Network Functions 279 12.6 Frequency Response from Pole-Zero Location 280 12.7 Ideal and Practical Filters 280 12.8 Passive and Active Filters 282 12.9 Bandpass Filters and Resonance 283 12.10 Natural Frequency and Damping Ratio 284 12.11 RLC Series Circuit; Series Resonance 284 12.12 Quality Factor 286 12.13 RLC Parallel Circuit; Parallel Resonance 287 12.14 Practical LC Parallel Circuit 288 12.15 Series-Parallel Conversions 289 12.16 Locus Diagrams 290 12.17 Scaling the Frequency Response of Filters 292CHAPTER 13 Two-port Networks 310 13.1 Terminals and Ports 310 13.2 Z-Parameters 310 13.3 T-Equivalent of Reciprocal Networks 312 13.4 Y-Parameters 312 13.5 Pi-Equivalent of Reciprocal Networks 314 13.6 Application of Terminal Characteristics 314 13.7 Conversion Between Z- and Y-Parameters 315 13.8 h-Parameters 316 13.9 g-Parameters 317 13.10 Transmission Parameters 317 13.11 Interconnecting Two-Port Networks 318 13.12 Choice of Parameter Type 320 13.13 Summary of Terminal Parameters and Conversion 320CHAPTER 14 Mutual Inductance and Transformers 334 14.1 Mutual Inductance 334 14.2 Coupling Coefﬁcient 335 14.3 Analysis of Coupled Coils 336 14.4 Dot Rule 338 14.5 Energy in a Pair of Coupled Coils 338 14.6 Conductively Coupled Equivalent Circuits 339 14.7 Linear Transformer 340 14.8 Ideal Transformer 342 14.9 Autotransformer 343 14.10 Reﬂected Impedance 344CHAPTER 15 Circuit Analysis Using Spice and Pspice 362 15.1 Spice and PSpice 362 15.2 Circuit Description 362 15.3 Dissecting a Spice Source File 363 15.4 Data Statements and DC Analysis 364 15.5 Control and Output Statements in DC Analysis 367 15.6 ´ Thevenin Equivalent 370 15.7 Op Amp Circuits 370
9. 9. Contents ix 15.8 AC Steady State and Frequency Response 373 15.9 Mutual Inductance and Transformers 375 15.10 Modeling Devices with Varying Parameters 375 15.11 Time Response and Transient Analysis 378 15.12 Specifying Other Types of Sources 379 15.13 Summary 382CHAPTER 16 The Laplace Transform Method 398 16.1 Introduction 398 16.2 The Laplace Transform 398 16.3 Selected Laplace Transforms 399 16.4 Convergence of the Integral 401 16.5 Initial-Value and Final-Value Theorems 401 16.6 Partial-Fractions Expansions 402 16.7 Circuits in the s-Domain 404 16.8 The Network Function and Laplace Transforms 405CHAPTER 17 Fourier Method of Waveform Analysis 420 17.1 Introduction 420 17.2 Trigonometric Fourier Series 421 17.3 Exponential Fourier Series 422 17.4 Waveform Symmetry 423 17.5 Line Spectrum 425 17.6 Waveform Synthesis 426 17.7 Effective Values and Power 427 17.8 Applications in Circuit Analysis 428 17.9 Fourier Transform of Nonperiodic Waveforms 430 17.10 Properties of the Fourier Transform 432 17.11 Continuous Spectrum 432APPENDIX A Complex Number System 451 A1 Complex Numbers 451 A2 Complex Plane 451 A3 Vector Operator j 452 A4 Other Representations of Complex Numbers 452 A5 Sum and Difference of Complex Numbers 452 A6 Multiplication of Complex Numbers 452 A7 Division of Complex Numbers 453 A8 Conjugate of a Complex Number 453APPENDIX B Matrices and Determinants 455 B1 Simultenaneous Equations and the Characteristic Matrix 455 B2 Type of Matrices 455 B3 Matrix Arithmetic 456 B4 Determinant of a Square Matrix 458 B5 Eigenvalues of a Square Matrix 460INDEX 461
12. 12. 2 INTRODUCTION [CHAP. 1 Table 1-2 Quantity Symbol SI Unit Abbreviation electric charge Q; q coulomb C electric potential V; v volt V resistance R ohm conductance G siemens S inductance L henry H capacitance C farad F frequency f hertz Hz force F; f newton N energy, work W; w joule J power P; p watt W magnetic ﬂux weber Wb magnetic ﬂux density B tesla TEXAMPLE 1.1. In simple rectilinear motion a 10-kg mass is given a constant acceleration of 2.0 m/s2 . (a) Find theacting force F. (b) If the body was at rest at t ¼ 0, x ¼ 0, ﬁnd the position, kinetic energy, and power for t ¼ 4 s.ðaÞ F ¼ ma ¼ ð10 kgÞð2:0 m=s2 Þ ¼ 20:0 kg Á m=s2 ¼ 20:0 NðbÞ At t ¼ 4 s; x ¼ 1 at2 ¼ 1 ð2:0 m=s2 Þð4 sÞ2 ¼ 16:0 m 2 2 KE ¼ Fx ¼ ð20:0 NÞð16:0 mÞ ¼ 3200 N Á m ¼ 3:2 kJ P ¼ KE=t ¼ 3:2 kJ=4 s ¼ 0:8 kJ=s ¼ 0:8 kW1.3 ELECTRIC CHARGE AND CURRENT The unit of current, the ampere (A), is deﬁned as the constant current in two parallel conductors ofinﬁnite length and negligible cross section, 1 meter apart in vacuum, which produces a force between theconductors of 2:0 Â 10À7 newtons per meter length. A more useful concept, however, is that currentresults from charges in motion, and 1 ampere is equivalent to 1 coulomb of charge moving across a ﬁxedsurface in 1 second. Thus, in time-variable functions, iðAÞ ¼ dq=dtðC/s). The derived unit of charge,the coulomb (C), is equivalent to an ampere-second. The moving charges may be positive or negative. Positive ions, moving to the left in a liquid orplasma suggested in Fig. 1-1(a), produce a current i, also directed to the left. If these ions cross theplane surface S at the rate of one coulomb per second, then the resulting current is 1 ampere. Negativeions moving to the right as shown in Fig. 1-1(b) also produce a current directed to the left. Table 1-3 Preﬁx Factor Symbol À12 pico 10 p nano 10À9 n micro 10À6 m milli 10À3 m centi 10À2 c deci 10À1 d kilo 103 k mega 106 M giga 109 G tera 1012 T
13. 13. CHAP. 1] INTRODUCTION 3 Fig. 1-1 Of more importance in electric circuit analysis is the current in metallic conductors which takes placethrough the motion of electrons that occupy the outermost shell of the atomic structure. In copper, forexample, one electron in the outermost shell is only loosely bound to the central nucleus and movesfreely from one atom to the next in the crystal structure. At normal temperatures there is constant,random motion of these electrons. A reasonably accurate picture of conduction in a copper conductoris that approximately 8:5 Â 1028 conduction electrons per cubic meter are free to move. The electroncharge is Àe ¼ À1:602 Â 10À19 C, so that for a current of one ampere approximately 6:24 Â 1018 elec-trons per second would have to pass a ﬁxed cross section of the conductor.EXAMPLE 1.2. A conductor has a constant current of ﬁve amperes. How many electrons pass a ﬁxed point onthe conductor in one minute? 5 A ¼ ð5 C=sÞð60 s=minÞ ¼ 300 C=min 300 C=min ¼ 1:87 Â 1021 electrons=min 1:602 Â 10À19 C=electron1.4 ELECTRIC POTENTIAL An electric charge experiences a force in an electric ﬁeld which, if unopposed, will accelerate theparticle containing the charge. Of interest here is the work done to move the charge against the ﬁeld assuggested in Fig. 1-2(a). Thus, if 1 joule of work is required to move the charge Q, 1 coulomb fromposition 0 to position 1, then position 1 is at a potential of 1 volt with respect to position 0; 1 V ¼ 1 J=C.This electric potential is capable of doing work just as the mass in Fig. 1-2(b), which was raised againstthe gravitational force g to a height h above the ground plane. The potential energy mgh represents anability to do work when the mass m is released. As the mass falls, it accelerates and this potential energyis converted to kinetic energy. Fig. 1-2
14. 14. 4 INTRODUCTION [CHAP. 1EXAMPLE 1.3. In an electric circuit an energy of 9.25 mJ is required to transport 0.5 mC from point a to point b.What electric potential diﬀerence exists between the two points? 9:25 Â 10À6 J 1 volt ¼ 1 joule per coulomb V¼ ¼ 18:5 V 0:5 Â 10À6 C1.5 ENERGY AND ELECTRICAL POWER Electric energy in joules will be encountered in later chapters dealing with capacitance and induc-tance whose respective electric and magnetic ﬁelds are capable of storing energy. The rate, in joules persecond, at which energy is transferred is electric power in watts. Furthermore, the product of voltageand current yields the electric power, p ¼ vi; 1 W ¼ 1 V Á 1 A. Also, V Á A ¼ ðJ=CÞ Á ðC=sÞ ¼ J=s ¼ W.In a more fundamental sense power is the time derivative p ¼ dw=dt, so that instantaneous power p isgenerally a function of time. In the following chapters time average power Pavg and a root-mean-square(RMS) value for the case where voltage and current are sinusoidal will be developed.EXAMPLE 1.4. A resistor has a potential diﬀerence of 50.0 V across its terminals and 120.0 C of charge per minutepasses a ﬁxed point. Under these conditions at what rate is electric energy converted to heat? ð120:0 C=minÞ=ð60 s=minÞ ¼ 2:0 A P ¼ ð2:0 AÞð50:0 VÞ ¼ 100:0 W Since 1 W ¼ 1 J/s, the rate of energy conversion is one hundred joules per second.1.6 CONSTANT AND VARIABLE FUNCTIONS To distinguish between constant and time-varying quantities, capital letters are employed for theconstant quantity and lowercase for the variable quantity. For example, a constant current of 10amperes is written I ¼ 10:0 A, while a 10-ampere time-variable current is written i ¼ 10:0 f ðtÞ A. Exam-ples of common functions in circuit analysis are the sinusoidal function i ¼ 10:0 sin !t ðAÞ and theexponential function v ¼ 15:0 eÀat (V). Solved Problems1.1 The force applied to an object moving in the x direction varies according to F ¼ 12=x2 (N). (a) Find the work done in the interval 1 m x 3 m. (b) What constant force acting over the same interval would result in the same work? ð3 3 12 À1 ðaÞ dW ¼ F dx so W¼ dx ¼ 12 ¼ 8J 1 x2 x 1 ðbÞ 8 J ¼ Fc ð2 mÞ or Fc ¼ 4 N1.2 Electrical energy is converted to heat at the rate of 7.56kJ/min in a resistor which has 270 C/min passing through. What is the voltage diﬀerence across the resistor terminals? From P ¼ VI, P 7:56 Â 103 J=min V¼ ¼ ¼ 28 J=C ¼ 28 V I 270 C=min
15. 15. CHAP. 1] INTRODUCTION 51.3 A certain circuit element has a current i ¼ 2:5 sin !t (mA), where ! is the angular frequency in rad/s, and a voltage diﬀerence v ¼ 45 sin !t (V) between terminals. Find the average power Pavg and the energy WT transferred in one period of the sine function. Energy is the time-integral of instantaneous power: ð 2=! ð 2=! 112:5 WT ¼ vi dt ¼ 112:5 sin2 !t dt ¼ ðmJÞ 0 0 ! The average power is then WT Pavg ¼ ¼ 56:25 mW 2=! Note that Pavg is independent of !.1.4 The unit of energy commonly used by electric utility companies is the kilowatt-hour (kWh). (a) How many joules are in 1 kWh? (b) A color television set rated at 75 W is operated from 7:00 p.m. to 11:30 p.m. What total energy does this represent in kilowatt-hours and in mega- joules? (a) 1 kWh ¼ ð1000 J=sÞð3600 s=hÞ ¼ 3:6 MJ (b) ð75:0 WÞð4:5 hÞ ¼ 337:5 Wh ¼ 0:3375 kWh ð0:3375 kWhÞð3:6 MJ=kWhÞ ¼ 1:215 MJ1.5 An AWG #12 copper wire, a size in common use in residential wiring, contains approximately 2:77 Â 1023 free electrons per meter length, assuming one free conduction electron per atom. What percentage of these electrons will pass a ﬁxed cross section if the conductor carries a constant current of 25.0 A? 25:0 C=s ¼ 1:56 Â 1020 electron=s 1:602 Â 10À19 C=electron ð1:56 Â 1020 electrons=sÞð60 s=minÞ ¼ 9:36 Â 1021 electrons=min 9:36 Â 1021 ð100Þ ¼ 3:38% 2:77 Â 10231.6 How many electrons pass a ﬁxed point in a 100-watt light bulb in 1 hour if the applied constant voltage is 120 V? 100 W ¼ ð120 VÞ Â IðAÞ I ¼ 5=6 A ð5=6 C=sÞð3600 s=hÞ ¼ 1:87 Â 1022 electrons per hour 1:602 Â 10À19 C=electron1.7 A typical 12 V auto battery is rated according to ampere-hours. A 70-A Á h battery, for example, at a discharge rate of 3.5 A has a life of 20 h. (a) Assuming the voltage remains constant, obtain the energy and power delivered in a complete discharge of the preceding batttery. (b) Repeat for a discharge rate of 7.0 A. (a) ð3:5 AÞð12 VÞ ¼ 42:0 W (or J/s) ð42:0 J=sÞð3600 s=hÞð20 hÞ ¼ 3:02 MJ (b) ð7:0 AÞð12 VÞ ¼ 84:0 W ð84:0 J=sÞð3600 s=hÞð10 hÞ ¼ 3:02 MJ
16. 16. 6 INTRODUCTION [CHAP. 1 The ampere-hour rating is a measure of the energy the battery stores; consequently, the energy trans- ferred for total discharge is the same whether it is transferred in 10 hours or 20 hours. Since power is the rate of energy transfer, the power for a 10-hour discharge is twice that in a 20-hour discharge. Supplementary Problems1.8 Obtain the work and power associated with a force of 7:5 Â 10À4 N acting over a distance of 2 meters in an elapsed time of 14 seconds. Ans. 1.5 mJ, 0.107 mW1.9 Obtain the work and power required to move a 5.0-kg mass up a frictionless plane inclined at an angle of 308 with the horizontal for a distance of 2.0 m along the plane in a time of 3.5 s. Ans. 49.0 J, 14.0 W1.10 Work equal to 136.0 joules is expended in moving 8:5 Â 1018 electrons between two points in an electric circuit. What potential diﬀerence does this establish between the two points? Ans. 100 V1.11 A pulse of electricity measures 305 V, 0.15 A, and lasts 500 ms. What power and energy does this represent? Ans. 45.75 W, 22.9 mJ1.12 A unit of power used for electric motors is the horsepower (hp), equal to 746 watts. How much energy does a 5-hp motor deliver in 2 hours? Express the answer in MJ. Ans. 26.9 MJ1.13 For t ! 0, q ¼ ð4:0 Â 10À4 Þð1 À eÀ250t Þ (C). Obtain the current at t ¼ 3 ms. Ans. 47.2 mA1.14 A certain circuit element has the current and voltage i ¼ 10eÀ5000t ðAÞ v ¼ 50ð1 À eÀ5000t Þ ðVÞ Find the total energy transferred during t ! 0. Ans. 50 mJ1.15 The capacitance of a circuit element is deﬁned as Q=V, where Q is the magnitude of charge stored in the element and V is the magnitude of the voltage diﬀerence across the element. The SI derived unit of capacitance is the farad (F). Express the farad in terms of the basic units. Ans. 1 F ¼ 1 A2 Á s4 =kg Á m2
17. 17. Circuit Concepts2.1 PASSIVE AND ACTIVE ELEMENTS An electrical device is represented by a circuit diagram or network constructed from series andparallel arrangements of two-terminal elements. The analysis of the circuit diagram predicts the perfor-mance of the actual device. A two-terminal element in general form is shown in Fig. 2-1, with a singledevice represented by the rectangular symbol and two perfectly conducting leads ending at connectingpoints A and B. Active elements are voltage or current sources which are able to supply energy to thenetwork. Resistors, inductors, and capacitors are passive elements which take energy from the sourcesand either convert it to another form or store it in an electric or magnetic ﬁeld. Fig. 2-1 Figure 2-2 illustrates seven basic circuit elements. Elements (a) and (b) are voltage sources and (c)and (d) are current sources. A voltage source that is not aﬀected by changes in the connected circuit is anindependent source, illustrated by the circle in Fig. 2-2(a). A dependent voltage source which changes insome described manner with the conditions on the connected circuit is shown by the diamond-shapedsymbol in Fig. 2-2(b). Current sources may also be either independent or dependent and the correspond-ing symbols are shown in (c) and (d). The three passive circuit elements are shown in Fig. 2-2(e), ( f ), and(g). The circuit diagrams presented here are termed lumped-parameter circuits, since a single element inone location is used to represent a distributed resistance, inductance, or capacitance. For example, a coilconsisting of a large number of turns of insulated wire has resistance throughout the entire length of thewire. Nevertheless, a single resistance lumped at one place as in Fig. 2-3(b) or (c) represents the dis-tributed resistance. The inductance is likewise lumped at one place, either in series with the resistance asin (b) or in parallel as in (c). 7 Copyright 2003, 1997, 1986, 1965 by The McGraw-Hill Companies, Inc. Click Here for Terms of Use.
18. 18. 8 CIRCUIT CONCEPTS [CHAP. 2 Fig. 2-2 Fig. 2-3 In general, a coil can be represented by either a series or a parallel arrangement of circuit elements.The frequency of the applied voltage may require that one or the other be used to represent the device.2.2 SIGN CONVENTIONS A voltage function and a polarity must be speciﬁed to completely describe a voltage source. Thepolarity marks, þ and À, are placed near the conductors of the symbol that identiﬁes the voltage source.If, for example, v ¼ 10:0 sin !t in Fig. 2-4(a), terminal A is positive with respect to B for 0 !t , andB is positive with respect to A for !t 2 for the ﬁrst cycle of the sine function. Fig. 2-4 Similarly, a current source requires that a direction be indicated, as well as the function, as shown inFig. 2-4(b). For passive circuit elements R, L, and C, shown in Fig. 2-4(c), the terminal where the currententers is generally treated as positive with respect to the terminal where the current leaves. The sign on power is illustrated by the dc circuit of Fig. 2-5(a) with constant voltage sourcesVA ¼ 20:0 V and VB ¼ 5:0 V and a single 5- resistor. The resulting current of 3.0 A is in the clockwisedirection. Considering now Fig. 2-5(b), power is absorbed by an element when the current enters theelement at the positive terminal. Power, computed by VI or I 2 R, is therefore absorbed by both theresistor and the VB source, 45.0 W and 15 W respectively. Since the current enters VA at the negativeterminal, this element is the power source for the circuit. P ¼ VI ¼ 60:0 W conﬁrms that the powerabsorbed by the resistor and the source VB is provided by the source VA .
19. 19. CHAP. 2] CIRCUIT CONCEPTS 9 Fig. 2-52.3 VOLTAGE-CURRENT RELATIONS The passive circuit elements resistance R, inductance L, and capacitance C are deﬁned by themanner in which the voltage and current are related for the individual element. For example, if thevoltage v and current i for a single element are related by a constant, then the element is a resistance,R is the constant of proportionality, and v ¼ Ri. Similarly, if the voltage is the time derivative of thecurrent, then the element is an inductance, L is the constant of proportionality, and v ¼ L di=dt.Finally, if the current in the element is the time derivative of the voltage, then the element is acapacitance, C is the constant of proportionality, and i ¼ C dv=dt. Table 2-1 summarizes these rela-tionships for the three passive circuit elements. Note the current directions and the correspondingpolarity of the voltages. Table 2-1 Circuit element Units Voltage Current Power ohms () v ¼ Ri v p ¼ vi ¼ i2 R i¼ (Ohms’s law) R Resistance ð di 1 di henries (H) v¼L i¼ v dt þ k1 p ¼ vi ¼ Li dt L dt Inductance ð 1 dv dv farads (F) v¼ i dt þ k2 i¼C p ¼ vi ¼ Cv C dt dt Capacitance
20. 20. 10 CIRCUIT CONCEPTS [CHAP. 22.4 RESISTANCE All electrical devices that consume energy must have a resistor (also called a resistance) in theircircuit model. Inductors and capacitors may store energy but over time return that energy to the sourceor to another circuit element. Power in the resistor, given by p ¼ vi ¼ i2 R ¼ v2 =R, is always positive asillustrated in Example 2.1 below. Energy is then determined as the integral of the instantaneous power ð t2 ð t2 ð 2 1 t2 2 w¼ p dt ¼ R i dt ¼ v dt t1 t1 R t1EXAMPLE 2.1. A 4.0- resistor has a current i ¼ 2:5 sin !t (A). Find the voltage, power, and energy over onecycle. ! ¼ 500 rad/s. v ¼ Ri ¼ 10:0 sin !t ðVÞ p ¼ vi ¼ i2 R ¼ 25:0 sin2 !t ðWÞ ðt ! t sin 2!t w ¼ p dt ¼ 25:0 À ðJÞ 0 2 4!The plots of i, p, and w shown in Fig. 2-6 illustrate that p is always positive and that the energy w, although afunction of time, is always increasing. This is the energy absorbed by the resistor. Fig. 2-6
21. 21. CHAP. 2] CIRCUIT CONCEPTS 112.5 INDUCTANCE The circuit element that stores energy in a magnetic ﬁeld is an inductor (also called an inductance).With time-variable current, the energy is generally stored during some parts of the cycle and thenreturned to the source during others. When the inductance is removed from the source, the magneticﬁeld will collapse; in other words, no energy is stored without a connected source. Coils found in electricmotors, transformers, and similar devices can be expected to have inductances in their circuit models.Even a set of parallel conductors exhibits inductance that must be considered at most frequencies. Thepower and energy relationships are as follows. ! di d 1 2 p ¼ vi ¼ L i¼ Li dt dt 2 ð t2 ð t2 1 2 2 wL ¼ p dt ¼ Li dt ¼ L½i2 À i1  t1 t1 2 Energy stored in the magnetic ﬁeld of an inductance is wL ¼ 1 Li2 . 2EXAMPLE 2.2. In the interval 0 t ð=50Þ s a 30-mH inductance has a current i ¼ 10:0 sin 50t (A). Obtain thevoltage, power, and energy for the inductance. ðt di v¼L ¼ 15:0 cos 50t ðVÞ p ¼ vi ¼ 75:0 sin 100t ðWÞ wL ¼ p dt ¼ 0:75ð1 À cos 100tÞ ðJÞ dt 0As shown in Fig. 2-7, the energy is zero at t ¼ 0 and t ¼ ð=50Þ s. Thus, while energy transfer did occur over theinterval, this energy was ﬁrst stored and later returned to the source. Fig. 2-7
22. 22. 12 CIRCUIT CONCEPTS [CHAP. 22.6 CAPACITANCE The circuit element that stores energy in an electric ﬁeld is a capacitor (also called capacitance).When the voltage is variable over a cycle, energy will be stored during one part of the cycle andreturned in the next. While an inductance cannot retain energy after removal of the source because themagnetic ﬁeld collapses, the capacitor retains the charge and the electric ﬁeld can remain after thesource is removed. This charged condition can remain until a discharge path is provided, at whichtime the energy is released. The charge, q ¼ Cv, on a capacitor results in an electric ﬁeld in thedielectric which is the mechanism of the energy storage. In the simple parallel-plate capacitor thereis an excess of charge on one plate and a deﬁciency on the other. It is the equalization of these chargesthat takes place when the capacitor is discharged. The power and energy relationships for the capa-citance are as follows. ! dv d 1 p ¼ vi ¼ Cv ¼ Cv2 dt dt 2 ð t2 ð t2 1 wC ¼ p dt ¼ Cv dv ¼ C½v2 À v2  2 1 t1 t1 2 The energy stored in the electric ﬁeld of capacitance is wC ¼ 1 Cv2 . 2EXAMPLE 2.3. In the interval 0 t 5 ms, a 20-mF capacitance has a voltage v ¼ 50:0 sin 200t (V). Obtain thecharge, power, and energy. Plot wC assuming w ¼ 0 at t ¼ 0. q ¼ Cv ¼ 1000 sin 200t ðmCÞ dv i¼C ¼ 0:20 cos 200t ðAÞ dt p ¼ vi ¼ 5:0 sin 400t ðWÞ ð t2 wC ¼ p dt ¼ 12:5½1 À cos 400t ðmJÞ t1In the interval 0 t 2:5 ms the voltage and charge increase from zero to 50.0 V and 1000 mC, respectively.Figure 2-8 shows that the stored energy increases to a value of 25 mJ, after which it returns to zero as the energyis returned to the source. Fig. 2-82.7 CIRCUIT DIAGRAMS Every circuit diagram can be constructed in a variety of ways which may look diﬀerent but are infact identical. The diagram presented in a problem may not suggest the best of several methods ofsolution. Consequently, a diagram should be examined before a solution is started and redrawn ifnecessary to show more clearly how the elements are interconnected. An extreme example is illustratedin Fig. 2-9, where the three circuits are actually identical. In Fig. 2-9(a) the three ‘‘junctions’’ labeled A
23. 23. CHAP. 2] CIRCUIT CONCEPTS 13are shown as two ‘‘junctions’’ in (b). However, resistor R4 is bypassed by a short circuit and may beremoved for purposes of analysis. Then, in Fig. 2-9(c) the single junction A is shown with its threemeeting branches. Fig. 2-92.8 NONLINEAR RESISTORS The current-voltage relationship in an element may be instantaneous but not necessarily linear. Theelement is then modeled as a nonlinear resistor. An example is a ﬁlament lamp which at higher voltagesdraws proportionally less current. Another important electrical device modeled as a nonlinear resistor isa diode. A diode is a two-terminal device that, roughly speaking, conducts electric current in onedirection (from anode to cathode, called forward-biased) much better than the opposite direction(reverse-biased). The circuit symbol for the diode and an example of its current-voltage characteristicare shown in Fig. 2-25. The arrow is from the anode to the cathode and indicates the forward directionði 0Þ. A small positive voltage at the diode’s terminal biases the diode in the forward direction and canproduce a large current. A negative voltage biases the diode in the reverse direction and produces littlecurrent even at large voltage values. An ideal diode is a circuit model which works like a perfect switch.See Fig. 2-26. Its ði; vÞ characteristic is v ¼ 0 when i ! 0 i ¼ 0 when v 0 The static resistance of a nonlinear resistor operating at ðI; VÞ is R ¼ V=I. Its dynamic resistance isr ¼ ÁV=ÁI which is the inverse of the slope of the current plotted versus voltage. Static and dynamicresistances both depend on the operating point.EXAMPLE 2.4. The current and voltage characteristic of a semiconductor diode in the forward direction ismeasured and recorded in the following table: v (V) 0.5 0.6 0.65 0.66 0.67 0.68 0.69 0.70 0.71 0.72 0.73 0.74 0.75 À4 i (mA) 2 Â 10 0.11 0.78 1.2 1.7 2.6 3.9 5.8 8.6 12.9 19.2 28.7 42.7 In the reverse direction (i.e., when v 0), i ¼ 4 Â 10À15 A. Using the values given in the table,calculate the static and dynamic resistances (R and r) of the diode when it operates at 30 mA, andﬁnd its power consumption p. From the table
24. 24. 14 CIRCUIT CONCEPTS [CHAP. 2 V 0:74 R¼ % ¼ 25:78 I 28:7 Â 10À3 ÁV 0:75 À 0:73 r¼ % ¼ 0:85 ÁI ð42:7 À 19:2Þ Â 10À3 p ¼ VI % 0:74 Â 28:7 Â 10À3 W ¼ 21:238 mWEXAMPLE 2.5. The current and voltage characteristic of a tungsten ﬁlament light bulb is measured and recordedin the following table. Voltages are DC steady-state values, applied for a long enough time for the lamp to reachthermal equilibrium. v (V) 0.5 1 1.5 2 3 3.5 4 4.5 5 5.5 6 6.5 7 7.5 8 i (mA) 4 6 8 9 11 12 13 14 15 16 17 18 18 19 20 Find the static and dynamic resistances of the ﬁlament and also the power consumption at the operating points(a) i ¼ 10 mA; (b) i ¼ 15 mA. V ÁV R¼ ; r¼ ; p ¼ VI I ÁI 2:5 3À2ðaÞ R% ¼ 250 ; r % ¼ 500 ; p % 2:5 Â 10 Â 10À3 W ¼ 25 mW 10 Â 10À3 ð11 À 9Þ Â 10À3 5 5:5 À 4:5ðbÞ R% ¼ 333 ; r % ¼ 500 ; p % 5 Â 15 Â 10À3 W ¼ 75 mW 15 Â 10À3 ð16 À 14Þ Â 10À3 Solved Problems2.1 A 25.0- resistance has a voltage v ¼ 150:0 sin 377t (V). Find the corresponding current i and power p. v i¼ ¼ 6:0 sin 377t ðAÞ p ¼ vi ¼ 900:0 sin2 377t ðWÞ R2.2 The current in a 5- resistor increases linearly from zero to 10 A in 2 ms. At t ¼ 2þ ms the current is again zero, and it increases linearly to 10 A at t ¼ 4 ms. This pattern repeats each 2 ms. Sketch the corresponding v. Since v ¼ Ri, the maximum voltage must be ð5Þð10Þ ¼ 50 V. In Fig. 2-10 the plots of i and v are shown. The identical nature of the functions is evident.2.3 An inductance of 2.0 mH has a current i ¼ 5:0ð1 À eÀ5000t Þ (A). Find the corresponding voltage and the maximum stored energy. di v¼L ¼ 50:0eÀ5000t ðVÞ dt In Fig. 2-11 the plots of i and v are given. Since the maximum current is 5.0 A, the maximum stored energy is 1 2 Wmax ¼ LI ¼ 25:0 mJ 2 max
25. 25. CHAP. 2] CIRCUIT CONCEPTS 15 Fig. 2-10 Fig. 2-112.4 An inductance of 3.0 mH has a voltage that is described as follows: for 0 t 2 ms, V ¼ 15:0 V and, for 2 t 4 ms, V ¼ À30:0 V. Obtain the corresponding current and sketch vL and i for the given intervals. For 0 t 2 ms, ðt ðt 1 1 i¼ v dt ¼ 15:0 dt ¼ 5 Â 103 t ðAÞ L 0 3 Â 10À3 0 For t ¼ 2 ms, i ¼ 10:0 A For 2 t 4 ms, ðt ðt 1 1 i¼ v dt þ 10:0 þ À30:0 dt L 2Â10À3 3 Â 10À3 2Â10À3 1 ¼ 10:0 þ ½À30:0t þ ð60:0 Â 10À3 Þ ðAÞ 3 Â 10À3 ¼ 30:0 À ð10 Â 103 tÞ ðAÞ See Fig. 2-12.2.5 A capacitance of 60.0 mF has a voltage described as follows: 0 t 2 ms, v ¼ 25:0 Â 103 t (V). Sketch i, p, and w for the given interval and ﬁnd Wmax . For 0 t 2 ms,
26. 26. 16 CIRCUIT CONCEPTS [CHAP. 2 Fig. 2-12 dv d i¼C ¼ 60 Â 10À6 ð25:0 Â 103 tÞ ¼ 1:5 A dt dt p ¼ vi ¼ 37:5 Â 103 t ðWÞ ðt wC ¼ p dt ¼ 1:875 Â 104 t2 ðmJÞ 0 See Fig. 2-13. Wmax ¼ ð1:875 Â 104 Þð2 Â 10À3 Þ2 ¼ 75:0 mJ 1 1 or Wmax ¼ CV2 ¼ ð60:0 Â 10À6 Þð50:0Þ2 ¼ 75:0 mJ max 2 2 Fig. 2-132.6 A 20.0-mF capacitance is linearly charged from 0 to 400 mC in 5.0 ms. Find the voltage function and Wmax . ! 400 Â 10À6 q¼ t ¼ 8:0 Â 10À2 t ðCÞ 5:0 Â 10À3 v ¼ q=C ¼ 4:0 Â 103 t ðVÞ 1 Vmax ¼ ð4:0 Â 103 Þð5:0 Â 10À3 Þ ¼ 20:0 V Wmax ¼ CV2 ¼ 4:0 mJ max 22.7 A series circuit with R ¼ 2, L ¼ 2 mH, and C ¼ 500 mF has a current which increases linearly from zero to 10 A in the interval 0 t 1 ms, remains at 10 A for 1 ms t 2 ms, and decreases linearly from 10 A at t ¼ 2 ms to zero at t ¼ 3 ms. Sketch vR , vL , and vC . vR must be a time function identical to i, with Vmax ¼ 2ð10Þ ¼ 20 V. For 0 t 1 ms, di di ¼ 10 Â 103 A=s and vL ¼ L ¼ 20 V dt dt When di=dt ¼ 0, for 1 ms t 2 ms, vL ¼ 0.
27. 27. CHAP. 2] CIRCUIT CONCEPTS 17 Assuming zero initial charge on the capacitor, ð 1 vC ¼ i dt C For 0 t 1 ms, ðt 1 vC ¼ 104 t dt ¼ 107 t2 ðVÞ 5 Â 10À4 0 This voltage reaches a value of 10 V at 1 ms. For 1 ms t 2 ms, 3 vC ¼ ð20 Â 10 Þðt À 10À3 Þ þ 10 ðVÞ See Fig. 2-14. Fig. 2-142.8 A single circuit element has the current and voltage functions graphed in Fig. 2-15. Determine the element. Fig. 2-15
28. 28. 18 CIRCUIT CONCEPTS [CHAP. 2 The element cannot be a resistor since v and i are not proportional. v is an integral of i. For 2 ms t 4 ms, i 6¼ 0 but v is constant (zero); hence the element cannot be a capacitor. For 0 t 2 ms, di ¼ 5 Â 103 A=s and v ¼ 15 V dt Consequently, 0 di L¼v ¼ 3 mH dt (Examine the interval 4 ms t 6 ms; L must be the same.)2.9 Obtain the voltage v in the branch shown in Fig. 2-16 for (a) i2 ¼ 1 A, (b) i2 ¼ À2 A, (c) i2 ¼ 0 A. Voltage v is the sum of the current-independent 10-V source and the current-dependent voltage source vx . Note that the factor 15 multiplying the control current carries the units . ðaÞ v ¼ 10 þ vx ¼ 10 þ 15ð1Þ ¼ 25 V ðbÞ v ¼ 10 þ vx ¼ 10 þ 15ðÀ2Þ ¼ À20 V ðcÞ v ¼ 10 þ 15ð0Þ ¼ 10 V Fig. 2-162.10 Find the power absorbed by the generalized circuit element in Fig. 2-17, for (a) v ¼ 50 V, (b) v ¼ À50 V. Fig. 2-17 Since the current enters the element at the negative terminal, ðaÞ p ¼ Àvi ¼ Àð50Þð8:5Þ ¼ À425 W ðbÞ p ¼ Àvi ¼ ÀðÀ50Þð8:5Þ ¼ 425 W2.11 Find the power delivered by the sources in the circuit of Fig. 2-18. 20 À 50 i¼ ¼ À10 A 3 The powers absorbed by the sources are:
29. 29. CHAP. 2] CIRCUIT CONCEPTS 19 Fig. 2-18 pa ¼ Àva i ¼ Àð20ÞðÀ10Þ ¼ 200 W pb ¼ vb i ¼ ð50ÞðÀ10Þ ¼ À500 W Since power delivered is the negative of power absorbed, source vb delivers 500 W and source va absorbs 200 W. The power in the two resistors is 300 W.2.12 A 25.0- resistance has a voltage v ¼ 150:0 sin 377t (V). Find the power p and the average power pavg over one cycle. i ¼ v=R ¼ 6:0 sin 377t ðAÞ p ¼ vi ¼ 900:0 sin2 377t ðWÞ The end of one period of the voltage and current functions occurs at 377t ¼ 2. For Pavg the integration is taken over one-half cycle, 377t ¼ . Thus, ð 1 Pavg ¼ 900:0 sin2 ð377tÞdð377tÞ ¼ 450:0 ðWÞ 02.13 Find the voltage across the 10.0- resistor in Fig. 2-19 if the control current ix in the dependent source is (a) 2 A and (b) À1 A. i ¼ 4ix À 4:0; vR ¼ iR ¼ 40:0ix À 40:0 ðVÞ ix ¼ 2; vR ¼ 40:0 V ix ¼ À1; vR ¼ À80:0 V Fig. 2-19 Supplementary Problems2.14 A resistor has a voltage of V ¼ 1:5 mV. Obtain the current if the power absorbed is (a) 27.75 nW and (b) 1.20 mW. Ans. 18.5 mA, 0.8 mA
30. 30. 20 CIRCUIT CONCEPTS [CHAP. 22.15 A resistance of 5.0 has a current i ¼ 5:0 Â 103 t (A) in the interval 0 ! t ! 2 ms. Obtain the instantaneous and average power. Ans. 125.0t2 (W), 167.0 (W)2.16 Current i enters a generalized circuit element at the positive terminal and the voltage across the element is 3.91 V. If the power absorbed is À25:0 mW, obtain the current. Ans. À6:4 mA2.17 Determine the single circuit element for which the current and voltage in the interval 0 ! 103 t ! are given by i ¼ 2:0 sin 103 t (mA) and v ¼ 5:0 cos 103 t (mV). Ans. An inductance of 2.5 mH 32.18 An inductance of 4.0 mH has a voltage v ¼ 2:0eÀ10 t (V). Obtain the maximum stored energy. At t ¼ 0, the current is zero. Ans. 0.5 mW2.19 A capacitance of 2.0 mF with an initial charge Q0 is switched into a series circuit consisting of a 10.0- resistance. Find Q0 if the energy dissipated in the resistance is 3.6 mJ. Ans. 120.0 mC2.20 Given that a capactance of C farads has a current i ¼ ðVm =RÞeÀt=ðRcÞ (A), show that the maximum stored 2 energy is 1 CVm . Assume the initial charge is zero. 22.21 The current after t ¼ 0 in a single circuit element is as shown in Fig. 2-20. Find the voltage across the element at t ¼ 6:5 ms, if the element is (a) 10 k, (b) 15 mH, (c) 0.3 nF with Qð0Þ ¼ 0. Ans. (a) 25 V; (b) À75 V; (c) 81.3 V Fig. 2-202.22 The 20.0-mF capacitor in the circuit shown in Fig. 2-21 has a voltage for t 0, v ¼ 100:0eÀt=0:015 (V). Obtain the energy function that accompanies the discharge of the capacitor and compare the total energy to that which is absorbed by the 750- resistor. Ans. 0.10 ð1 À eÀt=0:0075 Þ (J) Fig. 2-212.23 Find the current i in the circuit shown in Fig. 2-22, if the control v2 of the dependent voltage source has the value (a) 4 V, (b) 5 V, (c) 10 V. Ans. (a) 1 A; (b) 0 A; (c) À5 A2.24 In the circuit shown in Fig. 2-23, ﬁnd the current, i, given (a) i1 ¼ 2 A, i2 ¼ 0; (b) i1 ¼ À1 A; i2 ¼ 4 A; (c) i1 ¼ i2 ¼ 1 A. Ans. (a) 10 A; (b) 11 A; (c) 9A2.25 A 1-mF capacitor with an initial charge of 10À4 C is connected to a resistor R at t ¼ 0. Assume discharge current during 0 t 1 ms is constant. Approximate the capacitor voltage drop at t ¼ 1 ms for
31. 31. CHAP. 2] CIRCUIT CONCEPTS 21 Fig. 2-22 Fig. 2-23 (a) R ¼ 1 M; (b) R ¼ 100 k; (c) R ¼ 10 k. Hint: Compute the charge lost during the 1-ms period. Ans. (a) 0.1 V; (b) 1 V; (b) 10 V 62.26 The actual discharge current in Problem 2.25 is i ¼ ð100=RÞeÀ10 t=R A. Find the capacitor voltage drop at 1 ms after connection to the resistor for (a) R ¼ 1 M; (b) R ¼ 100 k; (c) R ¼ 10 k. Ans. (a) 0.1 V; (b) 1 V; (c) 9.52 V2.27 A 10-mF capacitor discharges in an element such that its voltage is v ¼ 2eÀ1000t . Find the current and power delivered by the capacitor as functions of time. Ans. i ¼ 20eÀ1000t mA, p ¼ vi ¼ 40eÀ1000t mJ2.28 Find voltage v, current i, and energy W in the capacitor of Problem 2.27 at time t ¼ 0, 1, 3, 5, and 10 ms. By integrating the power delivered by the capacitor, show that the energy dissipated in the element during the interval from 0 to t is equal to the energy lost by the capacitor. Ans. t v i W 0 2V 20 mA 20 mJ 1 ms 736 mV 7.36 mA 2.7 mJ 3 ms 100 mV 1 mA 0.05 mJ 5 ms 13.5 mV 135 mA % 0:001 mJ 10 ms 91 mV 0.91 mA %02.29 The current delivered by a current source is increased linearly from zero to 10 A in 1-ms time and then is decreased linearly back to zero in 2 ms. The source feeds a 3-k resistor in series with a 2-H inductor (see Fig. 2-24). (a) Find the energy dissipated in the resistor during the rise time ðW1 Þ and the fall time ðW2 Þ. (b) Find the energy delivered to the inductor during the above two intervals. (c) Find the energy delivered by the current source to the series RL combination during the preceding two intervals. Note: Series elements have the same current. The voltage drop across their combination is the sum of their individual voltages. Ans. ðaÞ W1 ¼ 100; W2 ¼ 200; (b) W1 ¼ 200; W2 ¼ À200; (c) W1 ¼ 300; W2 ¼ 0, all in joules2.30 The voltage of a 5-mF capacitor is increased linearly from zero to 10 V in 1 ms time and is then kept at that level. Find the current. Find the total energy delivered to the capacitor and verify that delivered energy is equal to the energy stored in the capacitor. Ans. i ¼ 50 mA during 0 t 1 ms and is zero elsewhere, W ¼ 250 mJ.
32. 32. 22 CIRCUIT CONCEPTS [CHAP. 2 Fig. 2-242.31 A 10-mF capacitor is charged to 2 V. A path is established between its terminals which draws a constant current of I0 . (a) For I0 ¼ 1 mA, how long does it take to reduce the capacitor voltage to 5 percent of its initial value? (b) For what value of I0 does the capacitor voltage remain above 90 percent of its initial value after passage of 24 hours? Ans. (a) 19 ms, (b) 23.15pA2.32 Energy gained (or lost) by an electric charge q traveling in an electric ﬁeld is qv, where v is the electric potential gained (or lost). In a capacitor with charge Q and terminal voltage V, let all charges go from one plate to the other. By way of computation, show that the total energy W gained (or lost) is not QV but QV=2 and explain why. Also note that QV=2 is equal to the initial energy content of the capacitor. Ð Â Ã Ans. W ¼ qvdt ¼ Q VÀ0 ¼ QV=2 ¼ 1 CV 2 . The apparent discrepancy is explained by the following. 2 2 The starting voltage vetween the two plates is V. As the charges migrate from one plate of the capacitor to the other plate, the voltage between the two plates drops and becomes zero when all charges have moved. The average of the voltage during the migration process is V=2, and therefore, the total energy is QV=2.2.33 Lightning I. The time proﬁle of the discharge current in a typical cloud-to-ground lightning stroke is modeled by a triangle. The surge takes 1 ms to reach the peak value of 100 kA and then is reduced to zero in 99 mS. (a) Find the electric charge Q discharged. (b) If the cloud-to-ground voltage before the discharge is 400 MV, ﬁnd the total energy W released and the average power P during the discharge. (c) If during the storm there is an average of 18 such lightning strokes per hour, ﬁnd the average power released in 1 hour. Ans. (a) Q ¼ 5 C; (b) W ¼ 109 J; P ¼ 1013 W; (c) 5 MW2.34 Lightning II. Find the cloud-to-ground capacitance in Problem 2.33 just before the lightning stroke. Ans. 12.5 mF2.35 Lightning III. The current in a cloud-to-ground lightning stroke starts at 200 kA and diminishes linearly to zero in 100 ms. Find the energy released W and the capacitance of the cloud to ground C if the voltage before the discharge is (a) 100 MV; (b) 500 MV. Ans. (a) W ¼ 5 Â 108 J; C ¼ 0:1 mF; (b) W ¼ 25 Â 108 J; C ¼ 20 nF2.36 The semiconductor diode of Example 2.4 is placed in the circuit of Fig. 2-25. Find the current for (a) Vs ¼ 1 V, (b) Vs ¼ À1 V. Ans. (a) 14 mA; (b) 02.37 The diode in the circuit of Fig. 2-26 is ideal. The inductor draws 100 mA from the voltage source. A 2-mF capacitor with zero initial charge is also connected in parallel with the inductor through an ideal diode such that the diode is reversed biased (i.e., it blocks charging of the capacitor). The switch s suddenly disconnects with the rest of the circuit, forcing the inductor current to pass through the diode and establishing 200 V at the capacitor’s terminals. Find the value of the inductor. Ans. L ¼ 8 H2.38 Compute the static and dynamic resistances of the diode of Example 2.4 at the operating point v ¼ 0:66 V. 0:66 0:67 À 0:65 Ans: R% ¼ 550 and r % ¼ 21:7 1:2 Â 10À3 ð1:7 À 0:78Þ Â 10À3
33. 33. CHAP. 2] CIRCUIT CONCEPTS 23 Fig. 2-25 Fig. 2-262.39 The diode of Example 2.4 operates within the range 10 i 20 mA. Within that range, approximate its terminal characteristic by a straight line i ¼ v þ
34. 34. , by specifying and
35. 35. . Ans. i ¼ 630 v À 4407 mA, where v is in V2.40 The diode of Example 2.4 operates within the range of 20 i 40 mA. Within that range, approximate its terminal characteristic by a straight line connecting the two operating limits. Ans. i ¼ 993:33 v À 702:3 mA, where v is in V2.41 Within the operating range of 20 i 40 mA, model the diode of Example 2.4 by a resistor R in series with a voltage source V such that the model matches exactly with the diode performance at 0.72 and 0.75 V. Find R and V. Ans. R ¼ 1:007 ; V ¼ 707 mV
36. 36. Circuit Laws3.1 INTRODUCTION An electric circuit or network consists of a number of interconnected single circuit elements of thetype described in Chapter 2. The circuit will generally contain at least one voltage or current source.The arrangement of elements results in a new set of constraints between the currents and voltages.These new constraints and their corresponding equations, added to the current-voltage relationshipsof the individual elements, provide the solution of the network. The underlying purpose of deﬁning the individual elements, connecting them in a network, andsolving the equations is to analyze the performance of such electrical devices as motors, generators,transformers, electrical transducers, and a host of electronic devices. The solution generally answersnecessary questions about the operation of the device under conditions applied by a source of energy.3.2 KIRCHHOFF’S VOLTAGE LAW For any closed path in a network, Kirchhoﬀ’s voltage law (KVL) states that the algebraic sum of thevoltages is zero. Some of the voltages will be sosurces, while others will result from current in passiveelements creating a voltage, which is sometimes referred to as a voltage drop. The law applies equallywell to circuits driven by constant sources, DC, time variable sources, vðtÞ and iðtÞ, and to circuits drivenby sources which will be introduced in Chapter 9. The mesh current method of circuit analysisintroduced in Section 4.2 is based on Kirchhoﬀ’s voltage law.EXAMPLE 3.1. Write the KVL equation for the circuit shown in Fig. 3-1. Fig. 3-1 24 Copyright 2003, 1997, 1986, 1965 by The McGraw-Hill Companies, Inc. Click Here for Terms of Use.
37. 37. CHAP. 3] CIRCUIT LAWS 25 Starting at the lower left corner of the circuit, for the current direction as shown, we have Àva þ v1 þ vb þ v2 þ v3 ¼ 0 Àva þ iR1 þ vb þ iR2 þ iR3 ¼ 0 va À vb ¼ iðR1 þ R2 þ R3 Þ3.3 KIRCHHOFF’S CURRENT LAW The connection of two or more circuit elements creates a junction called a node. The junctionbetween two elements is called a simple node and no division of current results. The junction of three ormore elements is called a principal node, and here current division does take place. Kirchhoﬀ’s currentlaw (KCL) states that the algrebraic sum of the currents at a node is zero. It may be stated alternativelythat the sum of the currents entering a node is equal to the sum of the currents leaving that node. Thenode voltage method of circuit analysis introduced in Section 4.3 is based on equations written at theprincipal nodes of a network by applying Kirchhoﬀ’s current law. The basis for the law is the con-servation of electric charge.EXAMPLE 3.2. Write the KCL equation for the principal node shown in Fig. 3-2. i1 À i2 þ i3 À i4 À i5 ¼ 0 i1 þ i3 ¼ i2 þ i4 þ i5 Fig. 3-23.4 CIRCUIT ELEMENTS IN SERIES Three passive circuit elements in series connection as shown in Fig. 3-3 have the same current i. Thevoltages across the elements are v1 , v2 , and v3 . The total voltage v is the sum of the individual voltages;v ¼ v1 þ v2 þ v3 . Fig. 3-3 If the elements are resistors,
38. 38. 26 CIRCUIT LAWS [CHAP. 3 v ¼ iR1 þ iR2 þ iR3 ¼ iðR1 þ R2 þ R3 Þ ¼ iReqwhere a single equivalent resistance Req replaces the three series resistors. The same relationshipbetween i and v will pertain. For any number of resistors in series, we have Req ¼ R1 þ R2 þ Á Á Á. If the three passive elements are inductances, di di di v ¼ L1 þ L2 þ L3 dt dt dt di ¼ ðL1 þ L2 þ L3 Þ dt di ¼ Leq dtExtending this to any number of inductances in series, we have Leq ¼ L1 þ L2 þ Á Á Á. If the three circuit elements are capacitances, assuming zero initial charges so that the constants ofintegration are zero, ð ð ð 1 1 1 v¼ i dt þ i dt þ i dt C1 C2 C3 ð 1 1 1 ¼ þ þ i dt C1 C2 C3 ð 1 ¼ i dt Ceq The equivalent capacitance of several capacitances in series is 1=Ceq ¼ 1=C1 þ 1=C2 þ Á Á Á.EXAMPLE 3.3. The equivalent resistance of three resistors in series is 750.0 . Two of the resistors are 40.0 and410.0 . What must be the ohmic resistance of the third resistor? Req ¼ R1 þ R2 þ R3 750:0 ¼ 40:0 þ 410:0 þ R3 and R3 ¼ 300:0 EXAMPLE 3.4. Two capacitors, C1 ¼ 2:0 mF and C2 ¼ 10:0 mF, are connected in series. Find the equivalentcapacitance. Repeat if C2 is 10.0 pF. C1 C2 ð2:0 Â 10À6 Þð10:0 Â 10À6 Þ Ceq ¼ ¼ ¼ 1:67 mF C1 þ C2 2:0 Â 10À6 þ 10:0 Â 10À6If C2 ¼ 10:0 pF, ð2:0 Â 10À6 Þð10:0 Â 10À12 Þ 20:0 Â 10À18 Ceq ¼ ¼ ¼ 10:0 pF 2:0 Â 10À6 þ 10:0 Â 10À12 2:0 Â 10À6where the contribution of 10:0 Â 10À12 to the sum C1 þ C2 in the denominator is negligible and therefore it can beomitted. Note: When two capacitors in series diﬀer by a large amount, the equivalent capacitance is essen-tially equal to the value of the smaller of the two.3.5 CIRCUIT ELEMENTS IN PARALLEL For three circuit elements connected in parallel as shown in Fig. 3-4, KCL states that the current ientering the principal node is the sum of the three currents leaving the node through the branches.
39. 39. CHAP. 3] CIRCUIT LAWS 27 Fig. 3-4 i ¼ i1 þ i2 þ i3 If the three passive circuit elements are resistances, v v v 1 1 1 1 i¼ þ þ ¼ þ þ v¼ v R1 R2 R3 R1 R2 R3 ReqFor several resistors in parallel, 1 1 1 ¼ þ þ ÁÁÁ Req R1 R2The case of two resistors in parallel occurs frequently and deserves special mention. The equivalentresistance of two resistors in parallel is given by the product over the sum. R1 R2 Req ¼ R1 þ R2EXAMPLE 3.5. Obtain the equivalent resistance of (a) two 60.0- resistors in parallel and (b) three 60.0-resistors in parallel. ð60:0Þ2ðaÞ Req ¼ ¼ 30:0 120:0 1 1 1 1ðbÞ ¼ þ þ Req ¼ 20:0 Req 60:0 60:0 60:0Note: For n identical resistors in parallel the equivalent resistance is given by R=n. Combinations of inductances in parallel have similar expressions to those of resistors in parallel: 1 1 1 L1 L2 ¼ þ þ ÁÁÁ and, for two inductances, Leq ¼ Leq L1 L2 L1 þ L2EXAMPLE 3.6. Two inductances L1 ¼ 3:0 mH and L2 ¼ 6:0 mH are connected in parallel. Find Leq . 1 1 1 ¼ þ and Leq ¼ 2:0 mH Leq 3:0 mH 6:0 mH With three capacitances in parallel, dv dv dv dv dv i ¼ C1 þ C2 þ C3 ¼ ðC1 þ C2 þ C3 Þ ¼ Ceq dt dt dt dt dt For several parallel capacitors, Ceq ¼ C1 þ C2 þ Á Á Á, which is of the same form as resistors in series.
40. 40. 28 CIRCUIT LAWS [CHAP. 33.6 VOLTAGE DIVISION A set of series-connected resistors as shown in Fig. 3-5 is referred to as a voltage divider. Theconcept extends beyond the set of resistors illustrated here and applies equally to impedances in series, aswill be shown in Chapter 9. Fig. 3-5 Since v1 ¼ iR1 and v ¼ iðR1 þ R2 þ R3 Þ, R1 v1 ¼ v R1 þ R2 þ R3EXAMPLE 3.7. A voltage divider circuit of two resistors is designed with a total resistance of the two resistorsequal to 50.0 . If the output voltage is 10 percent of the input voltage, obtain the values of the two resistors in thecircuit. v1 R1 ¼ 0:10 0:10 ¼ v 50:0 Â 103from which R1 ¼ 5:0 and R2 ¼ 45:0 .3.7 CURRENT DIVISION A parallel arrangement of resistors as shown in Fig. 3-6 results in a current divider. The ratio of thebranch current i1 to the total current i illustrates the operation of the divider. Fig. 3-6 v v v v i¼ þ þ and i1 ¼ R1 R2 R3 R1 i1 1=R1 R2 R3Then ¼ ¼ i 1=R1 þ 1=R2 þ 1=R3 R1 R2 þ R1 R3 þ R2 R3