Finishing materials: characteristics                                                  1                               P.U....
Finishing materials: characteristics                                              2                                 P.U. S...
Finishing materials: characteristics                                                 3                               N.C. ...
Finishing materials: characteristics                                                4                                N.C. ...
Finishing materials: characteristics                                                5                                A.C. ...
Finishing materials: characteristics                                               6                                   A.C...
Upcoming SlideShare
Loading in...5
×

Finishing notes

186

Published on

0 Comments
0 Likes
Statistics
Notes
  • Be the first to comment

  • Be the first to like this

No Downloads
Views
Total Views
186
On Slideshare
0
From Embeds
0
Number of Embeds
0
Actions
Shares
0
Downloads
1
Comments
0
Likes
0
Embeds 0
No embeds

No notes for slide

Finishing notes

  1. 1. Finishing materials: characteristics 1 P.U. LACQUER CLEARDescription: Two-pack components polyurethane clear on polyol resin and polyisocynanate resin.Use: Clear finish for where and extremely durable finish is requiredFeatures: • Tough film • Excellent chemical resistance • Excellent durabilityAppearance: High gloss finishesColour: ClearTechnical: Packing: 1 pail – 20 liters Mixing ratio= Base : hardener = 2:1 (by volume) Pot life: 4 hrs at 300C Specific gravity: 0.90 – 1.00 Flash point: 40CApplication: Application method: spray, brush can also be used. Thinner: P.U. thinner Thinning ratio: 40 – 50% if necessary Dry film thickness: 30 microns/coat Drying time: Touch dry – 60 minutes at 300C Hard dry – 24 hrs at 300C Over coating interval: 45 minutes at 300C Sanding time: 45 minutes at 300CPainting Surface preparation: remove oil, grease and foreign mattersspecification before coating. If necessary, prepare by sanding to establish a smooth clean surface. Sealer: 1 – 2 coat of P.U. sealer clear Topcoat: 1 – 2 coat of P.U. lacquer clearJasva Enterprise, 2A, Jln Desa Mewah 16, Taman Desa Mewah, 43500 Kajang,Selangor, Malaysia. Tel: 60-7-699-3999; H.P.: 6-012-213-0619 zaini@selectvest.com
  2. 2. Finishing materials: characteristics 2 P.U. SEALER CLEARDescription: Two-pack polyurethane based on polyol resin and polyisocynanate resin with suitable sanding agent.Use: Sealer for absorbent wooden materials to provide a smooth even surface upon light sanding.Features: • Excellent sanding properties • Good penetration into wooden substrates including cane • Transparent finish • Good heat resistance • Excellent applicabilityColour: ClearTechnical: Packing: 1 pail – 20 liters Mixing ratio= Base : hardener = 2:1 (by volume) Pot life: 3 hrs at 300C Specific gravity: 0.93 – 1.03 Flash point: 230CApplication: Application method: spray, brush can also be used. Thinner: P.U. thinner Thinning ratio: 20 - 40% if necessary Dry film thickness: 30 microns/coat Drying time: Touch dry – 10 minutes at 300C Hard dry – 4 hrs at 300C Over coating interval: 45 minutes at 300C Sanding time: 45 minutes at 300CPainting Surface preparation: remove oil, grease and foreign mattersspecification before coating. If necessary, prepare by sanding to establish a smooth clean surface. Sealer: 1 – 2 coat of P.U. sealer clear Topcoat: 1 – 2 coat of P.U. lacquer clearJasva Enterprise, 2A, Jln Desa Mewah 16, Taman Desa Mewah, 43500 Kajang,Selangor, Malaysia. Tel: 60-7-699-3999; H.P.: 6-012-213-0619 zaini@selectvest.com
  3. 3. Finishing materials: characteristics 3 N.C. LACQUER CLEARDescription: Nitrocellulose base clear lacquerUse: Finishing clear for timber wall paneling, wood, cane and other quality wooden surfaces in factory application.Features: • Tough and flexible film • Super high gloss • Fast dry • Transparent clear appearanceAppearance: High gloss finishesColour: ClearTechnical: Packing: 1 pail – 20 liters Specific gravity: 0.85 – 0.95 Flash point: 50CApplication: Application method: spray, brush can also be used. Thinner: TC303 Thinner Thinning ratio: 70 - 100% if necessary Dry film thickness: 20 microns/coat Drying time: Touch dry – 10 minutes at 300C Hard dry – 1 hr at 300C Over coating interval: 45 minutes at 300C Sanding time: 45 minutes at 300CPainting Surface preparation: remove oil, grease and foreign mattersspecification before coating. If necessary, prepare by sanding to establish a smooth clean surface. Sealer: 1 – 2 coat of N.C. sealer clear Topcoat: 1 – 2 coat of N.C. lacquer clearJasva Enterprise, 2A, Jln Desa Mewah 16, Taman Desa Mewah, 43500 Kajang,Selangor, Malaysia. Tel: 60-7-699-3999; H.P.: 6-012-213-0619 zaini@selectvest.com
  4. 4. Finishing materials: characteristics 4 N.C. SEALER CLEARDescription: A high built sanding sealer based on modified Nitrocellulose with special resinUse: Sealer for timber wall paneling, wood, cane and other quality wooden surfaces in factory application.Features: • Good filling property • Fast dry • Good dry sanding property • High built propertyColour: ClearTechnical: Packing: 1 pail – 20 liters Specific gravity: 0.90 – 1.00 Flash point: 40CApplication: Application method: spray, brush can also be used. Thinner: TC303 Thinner Thinning ratio: 50 - 80% if necessary Dry film thickness: 20 - 25 microns/coat Drying time: Touch dry – 10 minutes at 300C Hard dry – 30 minutes at 300C Over coating interval: 45 minutes at 300C Sanding time: 45 minutes at 300CPainting Surface preparation: remove oil, grease and foreign mattersspecification before coating. If necessary, prepare by sanding to establish a smooth clean surface. Sealer: 1 – 2 coat of N.C. sealer clear Topcoat: 1 – 2 coat of N.C. lacquer clearJasva Enterprise, 2A, Jln Desa Mewah 16, Taman Desa Mewah, 43500 Kajang,Selangor, Malaysia. Tel: 60-7-699-3999; H.P.: 6-012-213-0619 zaini@selectvest.com
  5. 5. Finishing materials: characteristics 5 A.C. SEALER CLEARDescription: Alkyd-melamine based acid curing clear sealer.Use: Sealer for timber wall paneling, wood, cane and other quality wooden surfaces in factory application.Features: • Quick dry • Good sanding property • Good heat resistance • Excellent resistance to water and household chemicalsColour: ClearTechnical: Packing: 1 pail – 20 liters Mixing ratio: Base: Hardener = 10:1 Pot life: 1 day at 300C Specific gravity: 1.02 – 1.12 Flash point: 70CApplication: Application method: spray, brush can also be used. Thinner: TC303 Thinner Thinning ratio: 10 - 30% Dry film thickness: 20 microns/coat Drying time: Touch dry – 8 - 15 minutes at 300C Hard dry – 30 – 60 minutes at 300C Over coating interval: 20 minutes at 300C or flash off 1 – 2 minutes at 500C 5 – 10 minutes for light sandingPainting Surface preparation: remove oil, grease and foreign mattersspecification before coating. If necessary, prepare by sanding to establish a smooth clean surface. Sealer: 1 coat of A.C. sealer clear Topcoat: 1 – 2 coat of A.C. top clearJasva Enterprise, 2A, Jln Desa Mewah 16, Taman Desa Mewah, 43500 Kajang,Selangor, Malaysia. Tel: 60-7-699-3999; H.P.: 6-012-213-0619 zaini@selectvest.com
  6. 6. Finishing materials: characteristics 6 A.C. TOP CLEARDescription: Alkyd-melamine based acid curing clear varnish.Use: Clear varnish for timber wall paneling, wood, cane and other quality wooden surfaces in factory application.Features: • Quick dry and good stack ability • Good heat resistance • Excellent mechanical resistance • Excellent resistance to water and household chemicalsColour: ClearGloss: Gloss, semi-gloss and mattTechnical: Packing: 1 pail – 20 liters Mixing ratio: Base: Hardener = 10:1 Pot life: 1 day at 300C Specific gravity: 0.95 – 1.05 Flash point: 290CApplication: Application method: spray, brush can also be used. Thinner: TC303 Thinner Thinning ratio: 20 - 50% if necessary Dry film thickness: 20 – 30 microns/coat Drying time: Touch dry – 8 - 15 minutes at 300C Hard dry – 30 – 60 minutes at 300C Over coating interval: 20 minutes at 300C or flash off 1 – 2 minutes at 500C 5 – 10 minutes for light sandingPainting Surface preparation: remove oil, grease and foreign mattersspecification before coating. If necessary, prepare by sanding to establish a smooth clean surface. Sealer: 1 coat of A.C. sealer clear Topcoat: 1 – 2 coat of A.C. top clearJasva Enterprise, 2A, Jln Desa Mewah 16, Taman Desa Mewah, 43500 Kajang,Selangor, Malaysia. Tel: 60-7-699-3999; H.P.: 6-012-213-0619 zaini@selectvest.com

×