Your SlideShare is downloading. ×
0
Website Ppt
Website Ppt
Website Ppt
Website Ppt
Website Ppt
Website Ppt
Website Ppt
Website Ppt
Upcoming SlideShare
Loading in...5
×

Thanks for flagging this SlideShare!

Oops! An error has occurred.

×
Saving this for later? Get the SlideShare app to save on your phone or tablet. Read anywhere, anytime – even offline.
Text the download link to your phone
Standard text messaging rates apply

Website Ppt

3,406

Published on

slides for PPT

slides for PPT

Published in: Business, Technology
0 Comments
0 Likes
Statistics
Notes
  • Be the first to comment

  • Be the first to like this

No Downloads
Views
Total Views
3,406
On Slideshare
0
From Embeds
0
Number of Embeds
0
Actions
Shares
0
Downloads
19
Comments
0
Likes
0
Embeds 0
No embeds

Report content
Flagged as inappropriate Flag as inappropriate
Flag as inappropriate

Select your reason for flagging this presentation as inappropriate.

Cancel
No notes for slide

Transcript

  • 1. Safety Spreadsheet #DIV/0   Fall Protection - Floor & Wall Openings   0 0 ! OSHA 1926.502 (b) #DIV/0 16 Guardrails constructed to withstand 200 lb Loads 0 0 (3) ! OSHA 1926.501 (b) #DIV/0 17 Guardrails installed at leading edge w/fall distance 6' or more 0 0 (13) ! OSHA 1926.502(b) #DIV/0 18 Guardrails installed at wall openings 19" wide or more 0 0 (2)(iv) ! OSHA 1926.501 (b) #DIV/0 19 Guardrails installed at window openings w/ sill height < 39" 0 0 (14) ! OSHA 1926.502(b) #DIV/0 20 Guardrail Component Heights: Top Rail 42" +/- 3" 0 0 (1) ! OSHA 1926.502(B) #DIV/0 21 Mid Rail 21" 0 0 (2) ! OSHA 1926.502(j) #DIV/0 22 Toe Board 4" High 0 0 (3) ! #DIV/0 23 Floor Openings>2"x2" covered OSHA 1926.500(b), 0 0 ! OSHA 1926.502(i) #DIV/0 24 Floor Openings>2"x2" marked "Cover" or "Hole" 0 0 (4) ! #DIV/0 25 Impalement hazards are guarded OSHA 1926.701(b) 0 0 !
  • 2. Framing  Structural Damage  2003 IRC Section 602.6 Drilling and notching-studs.  Studs in an exterior or bearing wall may be cut or notched to a depth not exceeding 25 percent of its width.  Studs in nonbearing walls may be notched to a depth not to exceed 40 percent of a single stud width.  Any stud may be bored or drilled, provided that the diameter of the resulting hole is no greater than 40 percent of the stud width, the edge of the hole is no closer than 5/8  inch to the edge of the stud
  • 3. Foundations  Beams  Beams are not being consistently installed with the correct width  Plans called for 12” wide beams  Beam is 9 ½” wide at bottom
  • 4. Framing  Studs over- notched to allow for plumbing stacks
  • 5. Enclosure  3 LAWS OF THERMODYNAMICS  HOT GOES TO COLD  HIGH PRESSURE GOES TO LOW PRESSURE  WET GOES TO DRY  KEEP BULK WATER OUT  LET WATER VAPOR ESCAPE  ALLEVIATE LOW PRESSURE IN HOUSES
  • 6. SAFETY  Scaffolds  Unsafe scaffold
  • 7. SWPPP  Permits  SWPP Plans  Inspection Reports  Posted Notices  Training  Site Maintenance  Terminations  Record Keeping
  • 8. SWPPP  Site Maintenance  Blowable trash is not being contained, and regularly removed

×