• Share
  • Email
  • Embed
  • Like
  • Save
  • Private Content
How To Install Silver Vapor 3-in-1 Flooring Underlayment
 

How To Install Silver Vapor 3-in-1 Flooring Underlayment

on

  • 1,575 views

This illustrated guide will show you with detailed step-by-step pictures how to install Silver Vapor 3-in-1 Flooring Underlayment. (Available here: http://ow.ly/yCiNz)

This illustrated guide will show you with detailed step-by-step pictures how to install Silver Vapor 3-in-1 Flooring Underlayment. (Available here: http://ow.ly/yCiNz)

Statistics

Views

Total Views
1,575
Views on SlideShare
309
Embed Views
1,266

Actions

Likes
0
Downloads
0
Comments
0

4 Embeds 1,266

http://www.bestlaminate.com 1248
https://www.bestlaminate.com 15
http://www.google.com 2
https://twitter.com 1

Accessibility

Categories

Upload Details

Uploaded via as Microsoft PowerPoint

Usage Rights

© All Rights Reserved

Report content

Flagged as inappropriate Flag as inappropriate
Flag as inappropriate

Select your reason for flagging this presentation as inappropriate.

Cancel
  • Full Name Full Name Comment goes here.
    Are you sure you want to
    Your message goes here
    Processing…
Post Comment
Edit your comment
  • How To Install Silver Vapor 3-in-1 Flooring Underlayment
  • Make it a DIY Project and save on your floor installation cost
  • Fact: Laying down underlayment is 10% of your installation cost
  • You may need: Enough vapor 3-in-1, Flooring, broom & dust pan, tape, scissors/utility knife
  • Step 1: Get cleaning! Subfloor should be clean and free of dirt.
  • Step 2: Subfloor check – subfloor should be in good condition without damages
  • Step 3: Fix Subfloor – subfloor needs fixing if: It is sloping, has excessive gabs, cracks or any areas with moisture.
  • Step 4: Time to get started – roll out vapor underlayment with the silver side facing down.
  • Quick hint: Overlapping film should be towards open room & Tape strip next to wall
  • Step 5: Install Parallel to the wall
  • Step 6: Cut your measured section with a utility knife
  • Step 7: You may add tape to temporally hold underlayment in place
  • Step 8: Install flooring on the underlayment section already installed
  • Cross stack your flooring – make sure to acclimate your flooring at least 48 hours before the installation
  • Step 9: Start your new roll – repeat step 4 and start your next roll
  • Step 10: Measure and Pre-cut next section
  • Step 11: Combine edges - butt edges together making sure to overlap only the silver film
  • Step 12: Remove adhesive layer and stick to underlament
  • Step 13: Use additional tape to secure rows if needed
  • Step 14: Continue Installation according to manufacturers instructions
  • Connect with us : www.bestlaminate.com / Facebook.com/Bestlaminate / Twitter.com/Bestlaminate

How To Install Silver Vapor 3-in-1 Flooring Underlayment How To Install Silver Vapor 3-in-1 Flooring Underlayment Presentation Transcript

  • How To Install Silver Vapor 3-in-1 Flooring Underlayment
  • Make it a DIY Project and save on your floor installation cost
  • Fact: Laying down underlayment is 10% of your installation cost
  • You may need: Enough vapor 3-in-1, Flooring, broom & dust pan, tape, scissors/utility knife
  • Step 1: Get cleaning! Subfloor should be clean and free of dirt.
  • Step 2: Subfloor check – subfloor should be in good condition without damages
  • Step 3: Fix Subfloor – subfloor needs fixing if: It is sloping, has excessive gabs, cracks or any areas with moisture.
  • Step 4: Time to get started – roll out vapor underlayment with the silver side facing down.
  • Quick hint: Overlapping film should be towards open room & Tape strip next to wall
  • Step 5: Install Parallel to the wall
  • Step 6: Cut your measured section with a utility knife
  • Step 7: You may add tape to temporally hold underlayment in place
  • Step 8: Install flooring on the underlayment section already installed
  • Cross stack your flooring – make sure to acclimate your flooring at least 48 hours before the installation
  • Step 9: Start your new roll – repeat step 4 and start your next roll
  • Step 10: Measure and Pre-cut next section
  • Step 11: Combine edges - butt edges together making sure to overlap only the silver film
  • Step 12: Remove adhesive layer and stick to underlament
  • Step 13: Use additional tape to secure rows if needed
  • Step 14: Continue Installation according to manufacturers instructions
  • Connect with us : www.bestlaminate.com / Facebook.com/Bestlaminate / Twitter.com/Bestlaminate www.Bestlaminate.com Facebook.com/Bestlaminate Twitter.com/Bestlaminate